Related Experiment Video

Updated: Aug 18, 2026

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion
09:32

Subject-specific Musculoskeletal Model for Studying Bone Strain During Dynamic Motion

Published on: April 11, 2018

The effect of stress concentration on bone remodeling: theoretical predictions

K Firoozbakhsh1, M Aleyaasin

  • 1Mechanical Engineering Department, Sharif University of Technology, Tehran, Iran.

Journal of Biomechanical Engineering
|November 1, 1989
PubMed

More Related Videos

Using Inducible Osteoblastic Lineage-Specific Stat3 Knockout Mice to Study Alveolar Bone Remodeling During Orthodontic Tooth Movement05:25

Using Inducible Osteoblastic Lineage-Specific Stat3 Knockout Mice to Study Alveolar Bone Remodeling During Orthodontic Tooth Movement

Published on: July 21, 2023

Tension-Free Weight-Bearing Model of Steroid-Induced Osteonecrosis of Femoral Head in Rats05:55

Tension-Free Weight-Bearing Model of Steroid-Induced Osteonecrosis of Femoral Head in Rats

Published on: September 27, 2024

Related Concept Videos

Bone Remodeling01:40

Bone Remodeling

Bone remodeling is a continuous and balanced process of bone resorption by osteoclasts and bone formation by osteoblasts. In adults, it helps maintain bone mass and calcium homeostasis. While mechanical stress can stimulate turnover as part of the normal maintenance and reparative process, several hormones also regulate bone remodeling.
Osteoclasts in Bone Remodeling01:31

Osteoclasts in Bone Remodeling

Osteoclasts are cells responsible for bone resorption and remodeling. They originate from hematopoietic progenitor cells present in the bone marrow. Numerous progenitor cells fuse to form multinucleated cells, each with 10-20 nuclei. A single osteoclast has a diameter of 150 to 200 µM. These cells have ruffled borders that break down the underlying bone tissue and release minerals such as calcium into the blood in bone resorption. Osteoclasts cling to bones with their ruffled edges during bone...
Bone Disorders01:29

Bone Disorders

Aging and its effect on bone remodeling is the most common cause of bone disorders. In young and healthy people, bone deposition and resorption happen at an equal rate to maintain optimal bone health.
Bone deposition is also affected by the levels of sex hormones like estrogen and testosterone that promote osteoblast activity and bone matrix synthesis. When the level of these hormones decreases due to aging, it causes a reduction in bone deposition. As a result, bone resorption by osteoclasts...
Stress Concentrations01:24

Stress Concentrations

Stress concentration is when stress intensifies near discontinuities such as holes or abrupt cross-sectional changes in a structural member. This localized stress can often surpass the average stress within the member. The stress distribution in flat bars, either with a circular hole or varying widths connected by fillets, can be determined experimentally using a photoelastic method. The results are based on ratios of geometric parameters like the ratio of the hole's radius to the smaller width...
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress concentration...