Related Experiment Video

Updated: Apr 25, 2026

Design, Fabrication, and Administration of the Hand Active Sensation Test HASTe
07:54

Design, Fabrication, and Administration of the Hand Active Sensation Test HASTe

Published on: September 8, 2015

8.5K

Occupational injuries in Ohio wood product manufacturing: a descriptive analysis with emphasis on saw-related

Lindsay Beery1, James R Harris, James W Collins

  • 1Emory Department of Emergency Medicine, Emory Center for Injury Control, Atlanta, Georgia.

American Journal of Industrial Medicine
|August 16, 2014
PubMed
Abstract

Keywords:
bladekickbackmachine safetysawswood

More Related Videos

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

11.8K
Author Spotlight: Deciphering the Long-Term Effects of Low-Level Blast Exposures in Mice06:00

Author Spotlight: Deciphering the Long-Term Effects of Low-Level Blast Exposures in Mice

Published on: May 24, 2024

1.3K

Related Concept Videos

Wood Products01:21

Wood Products

Wood products encompass a broad range of materials crafted from wood strands, veneers, lumber, and even waste wood-like shreds, designed for both structural and nonstructural purposes. Various specialized wood products have been developed to enhance strength, durability, and versatility in building applications.
Glue-laminated wood, often referred to as glulam, combines multiple smaller pieces of dimensional lumber using adhesives to form a single, larger piece. Cross-laminated timber consists...
427
Lumber01:19

Lumber

Lumber is derived from logs which are harvested, debarked, and processed into long pieces with a rectangular cross-section. The transformation of logs into lumber involves multiple steps, beginning with an automated saw that slices the log into slabs. These slabs are then transported via a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths.
Initially, the surfaces of these lumber pieces are rough, and their dimensions may vary slightly from one end to...
563
Lumber Defects01:23

Lumber Defects

Lumber defects, which can affect both the appearance and structural integrity of wood, include a variety of growth and manufacturing flaws. Growth defects such as knots and knotholes occur where branches were once attached to the tree trunk, with knotholes forming when these knots fall out. Other natural defects include decay and insect damage, which compromise the wood's strength and durability.
Shakes are minor fractures that run along or across the wood's annual rings, while wane is...
814
Introduction to Wood01:19

Introduction to Wood

Wood, derived from trees, is a versatile and widely used construction material. Trees feature a trunk surrounded by a protective layer of dead bark. Beneath this outer layer lies the living bark, followed by the cambium, and then the sapwood which transitions into heartwood as it matures. At the center of the trunk is the pith. The age of a tree can be discerned by examining its growth rings, which are concentric bands visible in the trunk's cross-section.
The structural integrity of the...
1.1K
Wood Panel Products01:18

Wood Panel Products

Wood panel products are essential materials used in construction for applications such as flooring, siding, and roofing, typically available in standard dimensions of 4 feet by 8 feet, with thicknesses varying from one-quarter of an inch to one and one-eighth inches. Among the most common types of wood panels is plywood, which is produced by gluing multiple layers of thin wood veneers under pressure. The grain of the outer veneers runs lengthwise, while the grains of the interior layers run...
529
Veneer01:19

Veneer

Veneer refers to a thin sheet of wood, typically produced to a thickness of about one-eighth of an inch or less. This material is crafted through various methods, the most common being rotary cutting. In this process, a log is mounted into a large lathe and spun against a knife edge, peeling off a continuous strip of wood as the knife penetrates deeper into the rotating log, creating a rotary-cut veneer.
Other veneering techniques include plain-slicing, quarter-slicing, and rift-slicing. These...
559