Related Experiment Video

Updated: Apr 24, 2026

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone ITZ
08:59

Determination of Aggregate Surface Morphology at the Interfacial Transition Zone ITZ

Published on: December 16, 2019

7.7K

Further study of multigranulation T-fuzzy rough sets

Wentao Li1, Xiaoyan Zhang1, Wenxin Sun1

  • 1School of Mathematics and Statistics, Chongqing University of Technology, Chongqing 400054, China.

Thescientificworldjournal
|September 13, 2014
PubMed

More Related Videos

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography09:00

Visualization of Failure and the Associated Grain-Scale Mechanical Behavior of Granular Soils under Shear using Synchrotron X-Ray Micro-Tomography

Published on: September 29, 2019

11.9K

Related Concept Videos

Types of Aggregate Grading01:15

Types of Aggregate Grading

Aggregate grading is crucial in economically obtaining a concrete mix with adequate strength, reasonable workability, and minimal segregation. There are four types of aggregate gradation: well-graded, uniformly (or one-sized) graded, gap-graded, and open-graded.
Well-graded aggregates include a complete range of necessary size fractions that fit together to create a dense matrix with minimal voids, represented by a smooth, continuous gradation curve. This type of grading ensures good...
1.9K
Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
1.2K
Sieve Analysis and Grading Curves01:19

Sieve Analysis and Grading Curves

Sieve analysis is a method used to determine the particle size distribution of aggregate materials. This process involves the following steps:
1.9K
Aggregates Classification01:29

Aggregates Classification

Aggregate classification is generally based on its size, petrographic characteristics, weight, and source. Size classification ranges from coarse to fine aggregates, defined by the size of the particles. Coarse aggregates are particles that do not pass through ASTM sieve No. 4, and aggregates that pass through the sieve are fine aggregates.
Petrographic classification groups aggregates based on common mineralogical characteristics. Some of the common mineral groups found in aggregates are...
991
Normal and Tangetial Components: Problem Solving01:24

Normal and Tangetial Components: Problem Solving

Consider a man with a mass of 70 kg seated in a chair connected to a pin support through a member BC. If the man maintains an upright position, the task is to determine the horizontal and vertical reactions of the chair on the man when the member makes a 45° angle with the horizontal. At this moment, the man has a speed of 5 m/s, increasing at a rate of 1 m/s².
743
Quantifying and Rejecting Outliers: The Grubbs Test01:02

Quantifying and Rejecting Outliers: The Grubbs Test

Sometimes, a data set can have a recorded numerical observation that greatly  deviates from the rest of the data. Assuming that the data is normally distributed, a statistical method called the Grubbs test can be used to determine whether the observation is truly an outlier.  To perform a two-tailed Grubbs test, first, calculate the absolute difference between the outlier and the mean. Then, calculate the ratio between this difference and the standard deviation of the sample. This...
4.0K