Related Experiment Video

Updated: Apr 23, 2026

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow
08:25

Measurements of Local Instantaneous Convective Heat Transfer in a Pipe - Single and Two-phase Flow

Published on: April 30, 2018

6.6K

Numerical investigation of heat transfer enhancement in a rectangular heated pipe for turbulent nanofluid

Hooman Yarmand1, Samira Gharehkhani1, Salim Newaz Kazi1

  • 1Department of Mechanical Engineering, University of Malaya, 50603 Kuala Lumpur, Malaysia.

Thescientificworldjournal
|September 26, 2014
PubMed

More Related Videos

Pool-Boiling Heat-Transfer Enhancement on Cylindrical Surfaces with Hybrid Wettable Patterns07:32

Pool-Boiling Heat-Transfer Enhancement on Cylindrical Surfaces with Hybrid Wettable Patterns

Published on: April 10, 2017

8.4K
Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel10:03

Uncoupling Coriolis Force and Rotating Buoyancy Effects on Full-Field Heat Transfer Properties of a Rotating Channel

Published on: October 5, 2018

7.5K

Related Concept Videos

Laminar Flow: Problem Solving01:24

Laminar Flow: Problem Solving

Laminar flow occurs when a fluid moves smoothly in parallel layers with minimal mixing and turbulence. In fluid mechanics, ensuring laminar flow within a pipe is essential for precise control of flow characteristics, especially in engineering applications. The key factor in determining whether flow remains laminar is the Reynolds number, a dimensionless quantity that depends on the fluid's velocity, density, viscosity, and the pipe's diameter. A Reynolds number of 2100 or lower...
622
Laminar Flow01:27

Laminar Flow

Laminar flow represents a smooth, orderly fluid motion where particles move along parallel paths, resulting in minimal mixing between layers. Streamlined particle paths characterize this flow regime and occur under conditions where viscous forces dominate over inertial forces. The distinction between laminar, transitional, and turbulent flow is primarily determined by the Reynolds number, a dimensionless quantity calculated as:
2.0K
General Characteristics of Pipe Flow I01:22

General Characteristics of Pipe Flow I

Pipe flow refers to the movement of fluids within fully enclosed conduits, typically cylindrical in shape, such as water pipes or hydraulic hoses. These conduits are designed to withstand high-pressure gradients that drive fluid movement, contrasting with open-channel flows, where gravity is the primary driving force. Rectangular conduits, like air conditioning and heating ducts, generally operate at lower pressures and are less suited for high-pressure applications.
The classification of fluid...
1.5K
Steady, Laminar Flow in Circular Tubes01:23

Steady, Laminar Flow in Circular Tubes

Hagen-Poiseuille flow describes a viscous fluid's steady, incompressible flow through a cylindrical tube with a constant radius R. This flow profile is often applied to understand fluid transport in narrow channels, such as capillaries. It serves as a foundational example of laminar flow. In this model, cylindrical coordinates (r,θ,z) are used to describe the radial (r), angular (θ), and axial (z) dimensions within the tube. For Hagen-Poiseuille flow, the velocity profile is purely...
2.0K
Single Pipe Systems01:24

Single Pipe Systems

In pipe flow analysis, problems are typically categorized into three types — Type I, Type II, and Type III — based on the known parameters and the desired outcome. Each type of problem addresses specific engineering requirements using fluid properties, pipe characteristics, and operational conditions.
In a Type I problem, fluid properties (density and viscosity), pipe characteristics (including diameter, length, and surface roughness), and the flow rate or average velocity are...
1.1K
Poiseuille's Law and Reynolds Number01:10

Poiseuille's Law and Reynolds Number

Any fluid in a horizontal tube can flow due to pressure differences—fluid flows from high to low pressure. The flow rate (Q) is the ratio of pressure difference and resistance through a horizontal tube. The greater the pressure difference, the higher the flow rate. The flow resistance is expressed as:
8.2K