Related Experiment Video

Updated: Apr 23, 2026

Methods of Ex Situ and In Situ Investigations of Structural Transformations: The Case of Crystallization of Metallic Glasses
08:55

Methods of Ex Situ and In Situ Investigations of Structural Transformations: The Case of Crystallization of Metallic Glasses

Published on: June 7, 2018

8.2K

Low-temperature excess heat capacity in fresnoite glass and crystal

Kensaku Nakamura1, Yoshihiro Takahashi1, Takumi Fujiwara1

  • 1Department of Applied Physics, Tohoku University, 6-6-05 Aoba-ku, Sendai 980-8579, Japan.

Scientific Reports
|October 7, 2014
PubMed

More Related Videos

Fluid-cell Raman Spectroscopy for operando Studies of Reaction and Transport Phenomena during Silicate Glass Corrosion06:48

Fluid-cell Raman Spectroscopy for operando Studies of Reaction and Transport Phenomena during Silicate Glass Corrosion

Published on: May 9, 2025

1.3K
Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures09:50

Measuring the Densities of Aqueous Glasses at Cryogenic Temperatures

Published on: June 28, 2017

8.3K

Related Concept Videos

Imperfections in Crystal Structure: Non-Stoichiometric Defects01:29

Imperfections in Crystal Structure: Non-Stoichiometric Defects

Non-stoichiometric defects refer to a type of defect in the crystal structure of a compound where the ratio of its constituent elements deviates from the ideal stoichiometric ratio. There are two main types of non-stoichiometric defects: metal excess defects and metal deficiency defects.Metal excess defects occur when there is a slight surplus of metal ions than what is required by the stoichiometric ratio of the compound. For example, heating a sodium chloride crystal in sodium vapor results...
110
Specific Heat01:16

Specific Heat

The specific heat capacity of a substance refers to the energy required to increase the temperature of one gram of that substance by one degree Celcius. Specific heat capacity is often represented in calories (cal), grams (g), and degrees Celsius (oC), but can also be expressed in joules (J), kilograms (kg), and Kelvin (K), among other units.
For example, increasing the temperature of one gram of water by 1°C requires one calorie of heat energy and can be written as 1 cal/g-°C, or...
57.6K
Heat Capacities of an Ideal Gas III01:25

Heat Capacities of an Ideal Gas III

The number of independent ways a gas molecule can move along straight line, rotate, and vibrate is called its degrees of freedom. Supposing d represents the number of degrees of freedom of an ideal gas, the molar heat capacity at constant volume of an ideal gas in terms of d is
2.1K
Imperfections in Crystal Structure: Stoichiometric Point Defects01:26

Imperfections in Crystal Structure: Stoichiometric Point Defects

Schottky defects arise when some lattice points in a crystal, such as those in NaCl, remain unoccupied, creating lattice vacancies without disturbing the overall electrical neutrality of the crystal. This defect is common in ionic crystals where the positive and negative ions are similar in size, as seen in sodium chloride and cesium chloride. The presence of Schottky defects enables the crystal to conduct electricity to a small extent through an ionic mechanism. Electric fields cause nearby...
133
Heat Capacities of an Ideal Gas I01:14

Heat Capacities of an Ideal Gas I

Heat capacity is the ratio of heat absorbed by the substance corresponding to its temperature change. It is also called thermal capacity and the SI unit of heat capacity is J/K. Whereas, specific heat capacity is defined as the amount of heat necessary to change the temperature of 1 kg of a substance by 1 K and is also called massic heat capacity. Its SI unit is J/kg⋅K.
Molar heat capacity quantifies the ratio of the amount of heat added (or removed) to increase (or decrease) the...
2.7K
Heat Capacities of an Ideal Gas II01:23

Heat Capacities of an Ideal Gas II

For a system that undergoes a thermodynamic process at a constant volume condition, the heat absorbed is used only to increase the system's internal energy and not for doing any kind of work. While for a system undergoing a thermodynamic process under a constant pressure condition, the amount of heat absorbed is used not only for increasing the internal energy (as a function of temperature) but also for doing some work. The molar heat capacity is the amount of heat required to increase the...
2.4K