Related Experiment Video

Updated: Apr 22, 2026

SIVQ-LCM Protocol for the ArcturusXT Instrument
07:37

SIVQ-LCM Protocol for the ArcturusXT Instrument

Published on: July 23, 2014

8.3K

First on-sky SCAO validation of full LQG control with vibration mitigation on the CANARY pathfinder

Gaetano Sivo, Caroline Kulcsár, Jean-Marc Conan

    Optics Express
    |October 17, 2014
    PubMed

    More Related Videos

    Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole09:37

    Visualization of Flow Field Around a Vibrating Pipeline Within an Equilibrium Scour Hole

    Published on: August 26, 2019

    5.3K
    Reduced-gravity Environment Hardware Demonstrations of a Prototype Miniaturized Flow Cytometer and Companion Microfluidic Mixing Technology13:59

    Reduced-gravity Environment Hardware Demonstrations of a Prototype Miniaturized Flow Cytometer and Companion Microfluidic Mixing Technology

    Published on: November 13, 2014

    13.0K

    Related Concept Videos

    Feedback control systems01:26

    Feedback control systems

    Feedback control systems are categorized in various ways based on their design, analysis, and signal types.
    Linear feedback systems are theoretical models that simplify analysis and design. These systems operate under the principle that their output is directly proportional to their input within certain ranges. For instance, an amplifier in a control system behaves linearly as long as the input signal remains within a specific range. However, most physical systems exhibit inherent nonlinearity...
    791
    Differential Leveling01:12

    Differential Leveling

    Differential leveling is a precise method in surveying used to determine the elevation difference between two points. Its primary goal is to establish accurate vertical measurements to create level surfaces or grade lines critical for designing and constructing infrastructures such as roads, bridges, and buildings.The procedure for differential leveling begins with setting up and leveling the instrument at a point where the benchmark can be seen. The level rod is held on the benchmark (BM), and...
    935
    Radial System Protection01:23

    Radial System Protection

    Radial systems employ time-delay overcurrent relays to reduce load interruptions. When a fault occurs, the nearest breaker opens first, while upstream breakers remain closed due to longer delay settings. This approach ensures minimal disruption to the rest of the system.
    In a radial system with a fault downstream of the third breaker, ideally, only the third breaker will open, isolating the fault and interrupting the load connected beyond it. The second breaker has a longer delay setting,...
    507
    Phase-lead and Phase-lag Controllers01:22

    Phase-lead and Phase-lag Controllers

    Understanding the working function of different types of controllers can be illustrated with practical analogies, such as adjusting a stereo's volume equalizer. Cranking up the bass involves a phase-lead controller, which functions as a high-pass filter, while increasing the treble uses a phase-lag controller, which acts as a low-pass filter. PD controllers, similar to high-pass filters, enhance the system's response to high-frequency components. PI controllers, akin to low-pass...
    646
    Pole and System Stability01:24

    Pole and System Stability

    The transfer function is a fundamental concept representing the ratio of two polynomials. The numerator and denominator encapsulate the system's dynamics. The zeros and poles of this transfer function are critical in determining the system's behavior and stability.
    Simple poles are unique roots of the denominator polynomial. Each simple pole corresponds to a distinct solution to the system's characteristic equation, typically resulting in exponential decay terms in the system's...
    1.3K
    Open and closed-loop control systems01:17

    Open and closed-loop control systems

    Control systems are foundational elements in automation and engineering. They are broadly categorized into open-loop and closed-loop systems. These classifications hinge on the presence or absence of feedback mechanisms, significantly influencing the system's performance, complexity, and application.
    An open-loop control system operates without feedback from the output. It consists of two primary elements: the controller and the controlled process. The controller receives an input signal...
    1.9K