Related Experiment Video

Updated: Apr 22, 2026

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters
15:25

Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

Published on: February 4, 2018

5.4K

Design of multichannel filters based on the use of periodic Cantor dielectric multilayers

Tzu-Chyang King, Chien-Jang Wu

    Applied Optics
    |October 17, 2014
    PubMed

    More Related Videos

    X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells10:16

    X-ray Beam Induced Current Measurements for Multi-Modal X-ray Microscopy of Solar Cells

    Published on: August 20, 2019

    15.5K
    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers13:44

    Simulation, Fabrication and Characterization of THz Metamaterial Absorbers

    Published on: December 27, 2012

    15.0K

    Related Concept Videos

    Design Example01:23

    Design Example

    The innovation of touch-tone telephony revolutionized the telecommunications industry by replacing the traditional rotary dial with a dual-tone multi-frequency (DTMF) signaling system. This system uses a matrix-style keypad with buttons arranged in four rows and three columns, creating 12 distinct signals each assigned to a pair of frequencies. Each button press results in a simultaneous generation of two sinusoidal tones – one from a low-frequency group (697 to 941 Hz) and one from a...
    688
    Passive Filters01:27

    Passive Filters

    Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
    Low-Pass Filters
    Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
    1.2K
    Active Filters01:25

    Active Filters

    Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
    1.4K
    Dielectric Polarization in a Capacitor01:31

    Dielectric Polarization in a Capacitor

    The presence of a dielectric medium in a capacitor not only changes the voltage and capacitance but also affects the electric field. In general, dielectrics can be of two types: polar and nonpolar. In a polar dielectric, the positive and negative charges in the molecules are separated by a distance and hence have a permanent dipole moment. In contrast, no such charge separation exists in a nonpolar dielectric, however the nonpolar molecules get polarized in the presence of an external electric...
    5.4K
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.8K
    Design Example: Underdamped Parallel RLC Circuit01:17

    Design Example: Underdamped Parallel RLC Circuit

    Consider designing an oscillator circuit, a crucial component in various electronic devices and systems. The objective is to create an oscillator circuit with specific characteristics: a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. To accomplish this, a parallel RLC circuit is employed, known for its ability to sustain oscillations at a resonant frequency. In this case, the damping factor is pivotal in achieving the desired performance.
    Starting with a fixed...
    809