Related Experiment Video

Updated: Apr 21, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

7.6K

Influence of thermal convection on density segregation in a vibrated binary granular system

C R K Windows-Yule1, T Weinhart2, D J Parker1

  • 1School of Physics and Astronomy, University of Birmingham, Edgbaston, Birmingham B15 2TT, United Kingdom.

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|October 30, 2014
PubMed

More Related Videos

Evolution of Staircase Structures in Diffusive Convection07:28

Evolution of Staircase Structures in Diffusive Convection

Published on: September 5, 2018

6.2K
Magnetically Induced Rotating Rayleigh-Taylor Instability06:42

Magnetically Induced Rotating Rayleigh-Taylor Instability

Published on: March 3, 2017

9.2K

Related Concept Videos

The Thermodynamics of Mixing01:28

The Thermodynamics of Mixing

Mixing is a fascinating phenomenon in thermodynamics, particularly when considering the Gibbs energy of a mixture at constant temperature and pressure. This energy, denoted as G, tends to decrease during spontaneous mixing processes, offering insights into the composition changes that occur.Imagine two ideal gases, initially separated in different containers, with amounts nA and nB, respectively, both at a temperature T and pressure p. The chemical potentials of these gases have their 'pure'...
137
Segregation in Fresh Concrete01:16

Segregation in Fresh Concrete

Segregation in fresh concrete is a phenomenon where the components of the concrete mix separate, leading to uneven distribution and compromised structural integrity. This separation typically occurs when concrete is subjected to excessive horizontal movement within forms, or when it is dropped from considerable heights or forced through narrow, winding paths. As a result, heavier coarse aggregate particles settle at the bottom, while lighter, finer materials such as cement and water rise to the...
1.2K
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
1.6K
Centrifugation01:05

Centrifugation

Centrifugation is a separation technique based on differences in density or size. It is commonly used to separate solids from aqueous interferents. During centrifugation, the sample is placed in centrifugation tubes and spun at high angular velocity, which allows centrifugal force to act differentially on the different densities or masses of the components. After spinning, the supernatant liquid is decanted. Depending on the specific application, either the pellet or the supernatant is retained...
6.8K
Density00:56

Density

Density is an important characteristic of substances, crucial in determining whether an object sinks or floats in a fluid. Its SI unit is kg/m3, and its cgs unit is g/cm3. The density of an object helps in identifying its composition, and also reveals information about the phase of the matter and its substructure. The densities of liquids and solids are roughly comparable, consistent with the fact that their atoms are in close contact. However, gases have much lower densities than liquids and...
16.6K
Density and Archimedes' Principle01:05

Density and Archimedes' Principle

When a lump of clay is dropped into water, it sinks. But if the same lump of clay is molded into the shape of a boat, it starts to float. Because of its shape, the clay boat displaces more water than the lump and experiences a greater buoyant force, even though its mass is the same. The same holds true for steel ships. The average density of an object majorly determines if the object will float. If an object's average density is less than that of the surrounding fluid, it will float. The...
6.4K