Related Experiment Video

Updated: Aug 7, 2026

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation
08:45

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Published on: July 21, 2014

[Some new points of view of cavity form]

M Slavcev, S Todorova

    Stomatologiia. Stomatology
    |September 1, 1989
    PubMed

    More Related Videos

    Rendering SiO2/Si Surfaces Omniphobic by Carving Gas-Entrapping Microtextures Comprising Reentrant and Doubly Reentrant Cavities or Pillars08:02

    Rendering SiO2/Si Surfaces Omniphobic by Carving Gas-Entrapping Microtextures Comprising Reentrant and Doubly Reentrant Cavities or Pillars

    Published on: February 11, 2020

    Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material07:42

    Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

    Published on: December 20, 2024

    Related Concept Videos

    Standing Waves in a Cavity01:28

    Standing Waves in a Cavity

    A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
    Deformations in a Transverse Cross Section01:21

    Deformations in a Transverse Cross Section

    When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
    As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
    Plastic Deformations of Members with a Single Plane of Symmetry01:21

    Plastic Deformations of Members with a Single Plane of Symmetry

    When a structural member undergoes plastic deformation due to bending, it is crucial to understand the position of the neutral axis and the stress distribution. This member, characterized by a single plane of symmetry, exhibits a uniform stress distribution, with negative stress above the neutral axis and positive stress below. Notably, the neutral axis does not align with the centroid of the cross-section. This misalignment is typical in cases where the cross-section is not rectangular or...
    Masonry Cavity Walls01:26

    Masonry Cavity Walls

    Cavity walls feature a hollow space between the outer and inner wythes, connected only by corrosion-resistant metal ties. When water seeps through the outer wythe, it descends within this cavity, intercepted by flashing and eventually exiting through weep holes. To enhance moisture resistance, the inner wythe's cavity side often receives damp-proofing, doubling as an air barrier. The cavity can also house insulation to mitigate heat transfer.
    Maintaining a clean cavity during construction is...
    Cavity Drainage and Flashings in Masonry walls01:20

    Cavity Drainage and Flashings in Masonry walls

    Typically, a cavity wall consists of two wythes separated by a gap of at least 2 inches, which may contain insulation while still maintaining a minimum clear space of 1 inch to facilitate adequate drainage. Advanced methods like the insertion of a continuous drainage mat can further reduce this space while ensuring effective moisture expulsion.
    Weep holes, strategically placed at the base of the cavity, are critical for draining accumulated water. These openings are created by leaving head...
    Cylinders in Three-Dimensional Space01:28

    Cylinders in Three-Dimensional Space

    A cylindrical surface is generated when a two-dimensional profile curve is translated along a straight line in three-dimensional space. The translated copies of the curve form a surface composed of parallel rulings, each oriented in the same fixed direction. This construction allows many three-dimensional forms to be described using relatively simple planar equations.In Cartesian coordinates, a cylindrical surface is often recognized by an equation that omits one of the three variables. For...