Related Experiment Video

Updated: Apr 17, 2026

Three-Dimensional Shape Modeling and Analysis of Brain Structures
05:33

Three-Dimensional Shape Modeling and Analysis of Brain Structures

Published on: November 14, 2019

7.7K

Canal shaping with one shape file and twisted files: a comparative study

Peddamallu Jitender Reddy1, Vedati Santosh Kumar2, Kumbakonam Aravind3

  • 1Senior Lecturer, Department of Conservative and Endodontics, Malla Reddy Dental College for Women , Hyderabad, India .

Journal of Clinical and Diagnostic Research : JCDR
|February 6, 2015
PubMed
Abstract

Keywords:
One shape fileRotary instruments NiTiShaping abilityTwisted files

More Related Videos

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

10.4K
Quantification of Strain in a Porcine Model of Skin Expansion Using Multi-View Stereo and Isogeometric Kinematics14:14

Quantification of Strain in a Porcine Model of Skin Expansion Using Multi-View Stereo and Isogeometric Kinematics

Published on: April 16, 2017

12.1K

Related Concept Videos

Bending of Curved Members - Strain Analysis01:14

Bending of Curved Members - Strain Analysis

The mechanics of deformation in curved members, such as beams or arches, under bending moments, involve complex responses. When such a member, symmetric about the y-axis and shaped like a segment of a circle centered at point C, is subjected to equal and opposite forces, its curvature and surface lengths change significantly. This alteration results in the shift of the curvature's center from C to C', indicating a tighter curve.
The important part of bending analysis for such a member...
668
Transformation of Plane Strain01:12

Transformation of Plane Strain

When analyzing elongated structures like bars subjected to uniformly distributed loads, it is essential to understand the transformation of plane strain when coordinate axes are rotated. This transformation helps to assess how material deformation characteristics vary with orientation, which is crucial in materials science and structural engineering.
Under plane strain conditions, typical for members where one dimension significantly exceeds the others, deformations and resultant strains are...
633
Design Example: Design of an Irrigation Channel01:27

Design Example: Design of an Irrigation Channel

Trapezoidal channels are widely used in irrigation systems due to their cost-effectiveness and efficiency in conveying water. Trapezoidal channels feature a flat bottom and sloping sides, making them stable and easier to construct compared to other shapes. The bottom width and side slope ratio are determined based on the required flow capacity and site conditions. The side slope is kept gentle for unlined channels to prevent soil erosion.Hydraulic parameters in channel design include the flow...
1.2K
Deformations in a Transverse Cross Section01:21

Deformations in a Transverse Cross Section

When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
758
Shape and Texture of Coarse Aggregate01:25

Shape and Texture of Coarse Aggregate

Aggregate shape is classified based on the relative sharpness or roundness of the edges and corners. This classification includes categories like rounded, angular, elongated, and flaky, each with specific characteristics. Rounded aggregates, fully shaped by attrition, are typical of river or seashore gravel, while angular aggregates, such as crushed rock, have well-defined edges. Aggregates that are elongated and flaky are less desirable, as they can reduce the workability and strength of...
1.3K
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the...
900