Related Experiment Video

Updated: Apr 17, 2026

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids
11:03

An Analog Macroscopic Technique for Studying Molecular Hydrodynamic Processes in Dense Gases and Liquids

Published on: December 4, 2017

9.1K

Exponential energy growth in adiabatically changing Hamiltonian systems.

Tiago Pereira1, Dmitry Turaev2

  • 1Department of Mathematics, Imperial College London SW7 2AZ, United Kingdom and London Mathematical Laboratory, London WC2N 6DF, United Kingdom.

Physical Review. E, Statistical, Nonlinear, and Soft Matter Physics
|February 14, 2015
PubMed
Summary

Energy in Hamiltonian systems grows exponentially with slow parameter changes. This universal dynamic is modeled using geometric Brownian motion, mirroring steady entropy increases over time.

More Related Videos

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section11:00

Experimental Investigation of Secondary Flow Structures Downstream of a Model Type IV Stent Failure in a 180° Curved Artery Test Section

Published on: July 19, 2016

12.0K
Submillisecond Conformational Changes in Proteins Resolved by Photothermal Beam Deflection10:02

Submillisecond Conformational Changes in Proteins Resolved by Photothermal Beam Deflection

Published on: February 18, 2014

9.5K

Related Concept Videos

Adiabatic Processes for an Ideal Gas01:18

Adiabatic Processes for an Ideal Gas

When an ideal gas is compressed adiabatically, that is, without adding heat, work is done on it, and its temperature increases. In an adiabatic expansion, the gas does work, and its temperature drops. Adiabatic compressions actually occur in the cylinders of a car, where the compressions of the gas-air mixture take place so quickly that there is no time for the mixture to exchange heat with its environment. Nevertheless, because work is done on the mixture during the compression, its...
4.5K
Pressure and Volume in an Adiabatic Process01:27

Pressure and Volume in an Adiabatic Process

Free expansion of a gas is an adiabatic process. However, there are few differences between free expansion and adiabatic expansion. During free expansion, no work is done, and there is no change in internal energy. But, for an adiabatic expansion, work is done, and there is a change in internal energy. During an adiabatic process, the relation between the pressure and volume is obtained from the condition for the adiabatic process, that is,
3.7K
The Joule and Joule–Thomson Experiments01:23

The Joule and Joule–Thomson Experiments

Consider an adiabatic system composed of two chambers, A and B, designed such that no heat flows into or out of the system. Initially, chamber A is filled with a gas at a fixed temperature T1, pressure p1, and volume V1, while chamber B is evacuated. The gas is then gradually forced through a rigid, porous barrier to chamber B, ultimately reaching temperature T2, pressure p2, and volume V2. A piston on the right side maintains a constant pressure (p2), which is lower than p1. The significant...
189
Work Done in an Adiabatic Process01:20

Work Done in an Adiabatic Process

Consider the adiabatic compression of an ideal gas in the cylinder of an automobile diesel engine. The gasoline vapor is injected into the cylinder of an automobile engine when the piston is in its expanded position. The temperature, pressure, and volume of the resulting gas-air mixture are 20 °C, 1.00 x 105 N/m2, and 240 cm3 , respectively. The mixture is then compressed adiabatically to a volume of 40 cm3. Note that, in the actual operation of an automobile engine, the compression is not...
4.5K
Energy Conservation and Bernoulli's Equation01:16

Energy Conservation and Bernoulli's Equation

Applying the conservation of energy principle or the work-energy theorem to an incompressible, inviscid fluid in laminar, steady, irrotational flow leads to Bernoulli's equation. It states that the sum of the fluid pressure, potential, and kinetic energy per unit volume is constant along a streamline.
All the terms in the equation have the dimension of energy per unit volume. The kinetic energy per unit volume is called the kinetic energy density, and the potential energy per unit volume is...
11.2K
Joule-Thomson Effect01:21

Joule-Thomson Effect

The Joule-Thomson effect, also known as the Joule-Kelvin effect, describes the temperature change of a fluid when it is forced through a valve or porous plug while keeping it in a thermally insulated environment. This experiment is called a throttling process. This is an important effect widely used in refrigeration and the liquefaction of gases.
This experiment forces high-pressure gas through a throttle valve or a porous plug to a lower-pressure region. The gas expands as it passes through to...
11.8K