Related Experiment Video

Updated: Apr 15, 2026

Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators
08:59

Modeling and Experimental Analysis of the Single-Shaft Coaxial Motor-Pump Assembly in Electrohydrostatic Actuators

Published on: June 13, 2022

3.1K

A standing wave linear ultrasonic motor operating in in-plane expanding and bending modes

Zhijiang Chen1, Xiaotian Li1, Penghong Ci1

  • 1Department of Materials Science and Engineering, College of Engineering, Peking University, Beijing 100871, China.

The Review of Scientific Instruments
|April 3, 2015
PubMed

More Related Videos

Fabrication and Characterization of Thickness Mode Piezoelectric Devices for Atomization and Acoustofluidics10:39

Fabrication and Characterization of Thickness Mode Piezoelectric Devices for Atomization and Acoustofluidics

Published on: August 5, 2020

7.6K
Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations06:51

Microparticle Manipulation by Standing Surface Acoustic Waves with Dual-frequency Excitations

Published on: August 21, 2018

7.6K

Related Concept Videos

Modes of Standing Waves - I01:03

Modes of Standing Waves - I

A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. A building may vibrate for several seconds with a driving frequency matching the building's natural frequency of vibration; this produces a resonance that results in one building collapsing while the neighboring buildings do not. Often, buildings of a certain height are devastated, while other taller buildings remain intact. This...
4.4K
Standing Waves in a Cavity01:28

Standing Waves in a Cavity

A household microwave and lasers are examples of standing electromagnetic waves in a cavity. When two conducting metal plates are placed parallel at the nodal planes, it creates a cavity where standing waves are formed. The cavity between the two planes is analogous to a stretched string held at the points x = 0 and x = L. Here, the distance 'L' between the two planes must be an integer multiple of half of the wavelength. The wavelengths that satisfy this condition are given by:
1.7K
Modes of Standing Waves: II01:04

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end....
2.0K
Standing Waves01:17

Standing Waves

Sometimes waves do not seem to move; rather, they just vibrate in place. Unmoving waves can be seen on the surface of a glass of milk kept in a refrigerator, which is one example of standing waves. Vibrations from the refrigerator motor create waves on the milk that oscillate up and down but do not seem to move across the surface. These waves are formed or created by the superposition of two or more identical moving waves in opposite directions. The waves move through each other, with their...
5.9K
Application of the Linear Momentum Equation01:15

Application of the Linear Momentum Equation

The application of the linear momentum equation can be used to analyze the forces needed to hold a 180-degree pipe bend in place with flowing water. In this case, water flows through the bend with a constant cross-sectional area of 0.01 square meters and a flow velocity of 15 meters per second. The pressure at the entrance is 0.2 Megapascals and the pressure at the exit is 0.16 Megapascals.
The goal is to determine the force components in the x and y directions to hold the pipe in place. Since...
607
Unsymmetric Bending01:18

Unsymmetric Bending

Unsymmetrical bending occurs when the bending moment applied to a structural member does not align with its principal axis. This misalignment leads to complex stress distributions and deflection patterns that differ from those in symmetrical bending, and are essential for designing structures to withstand different loading conditions. In unsymmetrical bending, the neutral axis—where stress is zero—does not necessarily align with the geometric axes of the cross-section. The...
986