Related Experiment Video

Updated: Apr 15, 2026

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices
11:24

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices

Published on: July 11, 2025

17.5K

Instability of a Möbius strip minimal surface and a link with systolic geometry

Adriana I Pesci1, Raymond E Goldstein1, Gareth P Alexander2

  • 1Department of Applied Mathematics and Theoretical Physics, Centre for Mathematical Sciences, University of Cambridge, Wilberforce Road, Cambridge CB3 0WA, United Kingdom.

Physical Review Letters
|April 11, 2015
PubMed

More Related Videos

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces08:05

Microtensiometer for Confocal Microscopy Visualization of Dynamic Interfaces

Published on: September 9, 2022

3.0K
Reconstitution of Membrane-Tethered Minimal Actin Cortices on Supported Lipid Bilayers11:55

Reconstitution of Membrane-Tethered Minimal Actin Cortices on Supported Lipid Bilayers

Published on: July 12, 2022

3.0K

Related Concept Videos

Pole and System Stability01:24

Pole and System Stability

The transfer function is a fundamental concept representing the ratio of two polynomials. The numerator and denominator encapsulate the system's dynamics. The zeros and poles of this transfer function are critical in determining the system's behavior and stability.
Simple poles are unique roots of the denominator polynomial. Each simple pole corresponds to a distinct solution to the system's characteristic equation, typically resulting in exponential decay terms in the system's...
1.3K
Stability of structures01:14

Stability of structures

In mechanical engineering, the stability of systems under various forces is critical for designing durable and efficient structures. One fundamental way to explore these concepts is by analyzing systems like two rods connected at a pivot point, O, with a torsional spring of spring constant k at the pivot point. This system is similar in appearance to a scissor jack used to change tires on a car. In this case, the arms of the linkage (equivalent to the rods in this system) are entirely vertical,...
627
Limits with Oscillating Discontinuities01:19

Limits with Oscillating Discontinuities

An oscillating discontinuity is a type of discontinuity in which a function’s values fluctuate infinitely often as the input approaches a particular point. Unlike jump discontinuities, where the function suddenly shifts between two values, or infinite discontinuities, where the function diverges without bound, an oscillating discontinuity arises from rapid back-and-forth variation. Because the function never stabilizes toward a single value, no finite limit exists at that point.One of the...
631
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
672
Stability of Equilibrium Configuration01:23

Stability of Equilibrium Configuration

Understanding the stability of equilibrium configurations is a fundamental part of mechanical engineering. In any system, there are three distinct types of equilibrium: stable, neutral, and unstable.
A stable equilibrium occurs when a system tends to return to its original position when given a small displacement, and the potential energy is at its minimum. An example of a stable equilibrium is when a cantilever beam is fixed at one end and a weight is attached to the other end. If the weight...
965
Stability01:28

Stability

The time response of a linear time-invariant (LTI) system can be divided into transient and steady-state responses. The transient response represents the system's initial reaction to a change in input and diminishes to zero over time. In contrast, the steady-state response is the behavior that persists after the transient effects have faded.
The stability of an LTI system is determined by the roots of its characteristic equation, known as poles. A system is stable if it produces a bounded...
486