Related Experiment Video

Updated: Apr 15, 2026

Biaxial Basal Tone and Passive Testing of the Murine Reproductive System Using a Pressure Myograph
09:59

Biaxial Basal Tone and Passive Testing of the Murine Reproductive System Using a Pressure Myograph

Published on: August 13, 2019

10.0K

[Physics of materials and female stress urinary continence: New concepts: I) Elasticity under bladder]

B Guerquin1

  • 1Service de gynécologie-obstétrique, centre hospitalier d'Orange (84100), avenue de Lavoisier, CS20184, 84104 Orange cedex, France.

Journal De Gynecologie, Obstetrique Et Biologie De La Reproduction
|April 14, 2015
PubMed
Abstract

Keywords:
Anatomie pelvienneAnterior vaginal wallContinence urinaire à l’effortParoi vaginale antérieurePelvic anatomyPhysiologiePhysiologyStress urinary continenceViscoelasticityViscoélasticité

More Related Videos

Evaluation of Biomaterials for Bladder Augmentation using Cystometric Analyses in Various Rodent Models10:19

Evaluation of Biomaterials for Bladder Augmentation using Cystometric Analyses in Various Rodent Models

Published on: August 9, 2012

20.0K
Isolation and Characterization of the Murine Uterosacral Ligaments and Pelvic Floor Organs05:47

Isolation and Characterization of the Murine Uterosacral Ligaments and Pelvic Floor Organs

Published on: March 3, 2023

2.2K

Related Concept Videos

Elastic Strain Energy for Normal Stresses01:22

Elastic Strain Energy for Normal Stresses

Strain energy quantifies the energy stored within a material due to deformation under loading conditions, a fundamental concept in materials science and engineering. The strain energy can be modeled when a material is subjected to axial loading with uniformly distributed stress. In this scenario, the stress experienced by the material is the internal force divided by the cross-sectional area, and the strain induced is directly proportional to this stress through the modulus of elasticity.
If...
707
Residual Stresses in Bending01:18

Residual Stresses in Bending

In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
659
Anatomy of the Genitourinary System II: Bladder and Urethra01:19

Anatomy of the Genitourinary System II: Bladder and Urethra

The lower urinary system consists of the urinary bladder and urethra, which are essential in storing and expelling urine from the body. Together with the internal and external sphincters, these structures work together to regulate urination effectively.Anatomy of the BladderThe urinary bladder is a muscular, stretchable organ behind the pubic bone and in front of the rectum. In females, the bladder is positioned anterior to the vagina and inferior to the uterus, while in males, it is located...
3.1K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
510
Strain and Elastic Modulus01:15

Strain and Elastic Modulus

The quantity that describes the deformation of a body under stress is known as strain. Strain is given as a fractional change in either length, volume, or geometry under tensile, volume (also known as bulk), or shear stress, respectively, and is a dimensionless quantity. The strain experienced by a body under tensile or compressive stress is called tensile or compressive strain, respectively. In contrast, the strain experienced under bulk stress and shear stress is known as volume and shear...
9.3K
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
774