Search research articles

ABOUT JoVE

Overview Leadership Blog JoVE Help Center

AUTHORS

Publishing Process Editorial Board Scope & Policies Peer Review FAQ Submit

LIBRARIANS

Testimonials Subscriptions Access Resources Library Advisory Board FAQ

RESEARCH

JoVE Journal Methods Collections JoVE Encyclopedia of Experiments Archive

EDUCATION

JoVE Core JoVE Business JoVE Science Education JoVE Lab Manual Faculty Resource Center Faculty Site

Terms & Conditions of Use

Related Concept Videos

Bonding and Strength of Aggregate

Bonding and Strength of Aggregate

The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...

Design Example: Distributing Reinforcements in Concrete Sections

Design Example: Distributing Reinforcements in Concrete Sections

The topic explores the practical aspects of adjusting steel reinforcements within a concrete beam section to meet specific design requirements. When designing a reinforced concrete beam, it is essential to distribute the steel reinforcements properly to ensure structural integrity and efficiency. The example provided details a scenario where a beam requires a total steel cross-section of 4 square inches. The engineer identifies that the available steel bars have a nominal diameter of 1.693...

Design Example: Managing Concrete Workability

Design Example: Managing Concrete Workability

This example deals with managing the workability of concrete for a raft foundation project under hot weather conditions. Workability is crucial for ensuring the concrete is easy to place, compact, and finish. In this scenario, a slump test — a common method to measure the workability of fresh concrete — initially indicated low workability. This was attributed to the rapid water loss from the concrete mix, exacerbated by the high temperatures causing the course aggregates to heat up.

Members Made of Elastoplastic Material

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...

The Extracellular Matrix

The Extracellular Matrix

Overview
In order to maintain tissue organization, many animal cells are surrounded by structural molecules that make up the extracellular matrix (ECM). Together, the molecules in the ECM maintain the structural integrity of tissue as well as the remarkable specific properties of certain tissues.
Composition of the Extracellular Matrix
The extracellular matrix (ECM) is commonly composed of ground substance, a gel-like fluid, fibrous components, and many structurally and functionally diverse...

The Extracellular Matrix

The Extracellular Matrix

You might also read

Related Articles

Articles linked to this work by shared authors, journal, and citation graph.

Sort by

Same author

Oncologic outcomes after poly-4-hydroxybutyrate scaffold in post-mastectomy breast reconstruction: a retrospective, multi-center cohort study.

World journal of surgical oncology·2026

Same author

Ora visual navigation course™ mobility test results in two individuals with <i>CEP290</i> LCA after intravitreal injection of antisense oligonucleotide.

Ophthalmic genetics·2026

Same author

Subpectoral vs Subfascial Cosmetic Breast Augmentation: Are We Ready to Settle?

Aesthetic surgery journal·2025

Same author

Capsule Preservation Breast Reconstruction Following Nipple-Sparing Mastectomy in Patients With Prior Breast Augmentation.

Annals of plastic surgery·2025

Same author

Discussion: Eyelid and Brow Rejuvenation: Technical Pearls and Outcomes of Upper Blepharoplasty with or without Ptosis Correction and Brow Lift.

Plastic and reconstructive surgery·2024

Same author

Aesthetic Breast Reconstruction: An Expert Video Roundtable Discussion.

Aesthetic surgery journal. Open forum·2024

Search research articles

Related Experiment Video

Updated: Apr 12, 2026

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes

Published on: May 17, 2018

Sientra high-strength cohesive shaped technique: roundtable discussion.

Michael R Schwartz¹, Peter J Capizzi¹, Kiya Movassaghi¹

¹Dr Schwartz is a plastic surgeon in private practice in Westlake Village, CA. Dr Capizzi is a plastic surgeon in private practice in Charlotte, NC. Dr Movassaghi is a Clinical Assistant Professor of Plastic and Reconstructive Surgery at Oregon Health and Science University, Eugene. Dr Talmor is an Associate Professor of Plastic and Reconstructive Surgery at Weill Cornell Medical Center, New York City, and an Attending Surgeon at New York Presbyterian Hospital, New York City.

Aesthetic Surgery Journal

|May 8, 2015

Summary

Plastic surgeons reviewed their experiences with Sientra High-Strength Cohesive (HSC+) shaped silicone gel breast implants. These textured implants aided in achieving successful outcomes in over 700 patients.

More Related Videos

Fibroblast Derived Human Engineered Connective Tissue for Screening Applications

Fibroblast Derived Human Engineered Connective Tissue for Screening Applications

Published on: August 20, 2021

Manufacturing of Three-dimensionally Microstructured Nanocomposites through Microfluidic Infiltration

Manufacturing of Three-dimensionally Microstructured Nanocomposites through Microfluidic Infiltration

Published on: March 12, 2014

Related Experiment Videos

Last Updated: Apr 12, 2026

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes

Magnet Assisted Composite Manufacturing: A Flexible New Technique for Achieving High Consolidation Pressure in Vacuum Bag/Lay-Up Processes

Published on: May 17, 2018

Fibroblast Derived Human Engineered Connective Tissue for Screening Applications

Fibroblast Derived Human Engineered Connective Tissue for Screening Applications

Published on: August 20, 2021

Manufacturing of Three-dimensionally Microstructured Nanocomposites through Microfluidic Infiltration

Manufacturing of Three-dimensionally Microstructured Nanocomposites through Microfluidic Infiltration

Published on: March 12, 2014

Area of Science:

Plastic surgery
Aesthetic surgery
Breast augmentation

Background:

Expert panel discussion on Sientra High-Strength Cohesive (HSC+) shaped silicone gel breast implants.
Surgeons convened to share clinical experiences with HSC+ implants.

Observation:

The panel comprised board-certified plastic surgeons with extensive experience.
A combined total of over 700 patients have been implanted with HSC+ devices.
Discussions covered preoperative planning, surgical techniques, and practice integration.

Findings:

Breakthrough cases were presented, highlighting successful outcomes.
The HSC+ textured implants were instrumental in achieving desired results.
Surgeons shared practical tips for integrating the implants into their practice.

Implications:

Provides insights into the practical application and success of HSC+ implants.
Offers valuable information for plastic surgeons considering these devices.
Contributes to the understanding of textured breast implant performance in aesthetic surgery.