Related Experiment Video

Updated: Apr 10, 2026

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials
11:28

A Coupled Experiment-finite Element Modeling Methodology for Assessing High Strain Rate Mechanical Response of Soft Biomaterials

Published on: May 18, 2015

13.1K

Determinants of injuries in passenger vessel accidents

Tsz Leung Yip1, Di Jin2, Wayne K Talley3

  • 1C Y. Tung International Centre for Maritime Studies, Department of Logistics and Maritime Studies, The Hong Kong Polytechnic University, Hong Kong, China.

Accident; Analysis and Prevention
|June 13, 2015
PubMed

Keywords:
FerryOcean cruiseRiver cruiseVessel accidents

More Related Videos

A Test Bed to Examine Helmet Fit and Retention and Biomechanical Measures of Head and Neck Injury in Simulated Impact07:30

A Test Bed to Examine Helmet Fit and Retention and Biomechanical Measures of Head and Neck Injury in Simulated Impact

Published on: September 21, 2017

9.5K
Mechanical Vessel Injury in Zebrafish Embryos06:38

Mechanical Vessel Injury in Zebrafish Embryos

Published on: February 17, 2015

7.8K

Related Concept Videos

Design Consideration01:22

Design Consideration

Designing a structure involves a series of considerations, primarily the material's ultimate strength, calculated through tests that measure changes under increased force until the material reaches its breaking point or limit. The ultimate load, where the material breaks, is divided by its original cross-sectional area, resulting in the ultimate normal stress or strength. The ultimate shearing stress is another significant factor taken into account.
The factor of safety is another key...
642
Constraints and Statical Determinacy01:26

Constraints and Statical Determinacy

In structural engineering, the equilibrium of a system is not only determined by its equations of equilibrium but also with the help of constraints. Constraints refer to restrictions on the motion of a system. The proper combinations of constraints can minimize the total number of constraints needed to maintain a system in mechanical equilibrium. When this happens, the system is said to be statically determinate. For such systems, the unknown reaction supports can be estimated using equilibrium...
1.1K
Determination of Expected Frequency01:08

Determination of Expected Frequency

Suppose one wants to test independence between the two variables of a contingency table. The values in the table constitute the observed frequencies of the dataset. But how does one determine the expected frequency of the dataset? One of the important assumptions is that the two variables are independent, which means the variables do not influence each other. For independent variables, the statistical probability of any event involving both variables is calculated by multiplying the individual...
2.7K
Saint-Venant's Principle01:18

Saint-Venant's Principle

The principle of Saint-Venant postulates that the stress distribution within a structural member does not rely on the precise method of load application except in the vicinity of the load application points. Consider a scenario where loads are centrally applied on two plates. In this case, the plates move toward each other without any rotation. This movement causes the member to contract in length and expand in width and thickness. Uniform deformation across all elements and maintaining...
2.0K
Major Losses in Pipes01:28

Major Losses in Pipes

When a fluid flows through a pipe, it experiences energy losses due to frictional resistance along the pipe walls, known as major losses. These energy losses result in a pressure drop, which varies based on the flow conditions — whether laminar or turbulent — and the specific physical properties of the fluid and pipe.
Fluid flow can be classified as laminar or turbulent, primarily based on the Reynolds number. This dimensionless number reflects the relative influence of inertial to viscous...
2.7K
Hypothesis Test for Test of Independence01:16

Hypothesis Test for Test of Independence

The test of independence is a chi-square-based test used to determine whether two variables or factors are independent or dependent. This hypothesis test is used to examine the independence of the variables. One can construct two qualitative survey questions or experiments based on the variables in a contingency table. The goal is to see if the two variables are unrelated (independent) or related (dependent). The null and alternative hypotheses for this test are:
H0: The two variables (factors)...
8.4K