Related Experiment Video

Updated: Jan 26, 2026

Author Spotlight: Enhancing CryoEM Sample Preparation Using Graphene Monolayer on Microscopy Grids
07:57

Author Spotlight: Enhancing CryoEM Sample Preparation Using Graphene Monolayer on Microscopy Grids

Published on: November 10, 2023

26.3K

Suspended monolayer graphene under true uniaxial deformation

Ioannis Polyzos1, Massimiliano Bianchi, Laura Rizzi

  • 1Institute of Chemical Engineering Sciences, Foundation of Research and Technology-Hellas (FORTH/ICE-HT), Patras, Greece. c.galiotis@iceht.forth.gr ipolyzos@iceht.forth.gr.

Nanoscale
|July 15, 2015
PubMed

More Related Videos

Author Spotlight: Enhancing CryoEM Resolution Using Graphene-Coated Grids06:53

Author Spotlight: Enhancing CryoEM Resolution Using Graphene-Coated Grids

Published on: September 8, 2023

3.9K
Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection07:51

Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection

Published on: February 1, 2022

3.8K

Related Concept Videos

True Stress and True Strain01:28

True Stress and True Strain

Engineering stress is calculated as the load divided by the original, undeformed cross-sectional area. It approximates a material under load. This approximation is especially relevant post-yield in ductile materials. Though engineering stress-strain diagrams are often used for their convenience and accessibility, they can sometimes fall short in accuracy, particularly when dealing with large strain values.
In contrast, true stress offers a more precise portrayal. It is computed by dividing the...
815
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
444
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
412
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
377
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
485
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
457