Related Experiment Video

Updated: Apr 6, 2026

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source
12:19

Measurement of Quantum Interference in a Silicon Ring Resonator Photon Source

Published on: April 4, 2017

9.0K

BER evaluation of a low-crosstalk silicon integrated multi-microring network-on-chip

Fabrizio Gambini, Stefano Faralli, Paolo Pintus

    Optics Express
    |July 21, 2015
    PubMed

    More Related Videos

    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station05:57

    Characterization of SiN Integrated Optical Phased Arrays on a Wafer-Scale Test Station

    Published on: April 1, 2020

    8.7K
    Laser-induced Forward Transfer for Flip-chip Packaging of Single Dies08:21

    Laser-induced Forward Transfer for Flip-chip Packaging of Single Dies

    Published on: March 20, 2015

    13.0K

    Related Concept Videos

    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    836
    Semiconductors01:22

    Semiconductors

    There is variation in the electrical conductivity of materials - metals, semiconductors, and insulators that are showcased with the help of the energy band diagrams.
    Metals such as copper (Cu), zinc (Zn), or lead (Pb) have low resistivity and feature conduction bands that are either not fully occupied or overlap with the valence band, making a bandgap non-existent. This allows electrons in the highest energy levels of the valence band to easily transition to the conduction band upon gaining...
    1.9K
    Biasing of FET01:22

    Biasing of FET

    Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
    In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
    958
    Metal-Semiconductor Junctions01:24

    Metal-Semiconductor Junctions

    The contact of metal and semiconductor can lead to the formation of a junction with either Schottky or Ohmic behavior.
    Schottky Barriers
    Schottky barriers arise when a metal with a work function (Φm) contacts a semiconductor with a different work function (Φs). Initially, electrons transfer until the Fermi levels of the metal and semiconductor align at equilibrium. For instance, if Φm > Φs, the semiconductor Fermi level is higher than the metal's before contact. The...
    1.4K
    Design Example: Capacitance Multiplier Circuit01:20

    Design Example: Capacitance Multiplier Circuit

    In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
    The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
    1.8K
    Bus Impedance Matrix01:24

    Bus Impedance Matrix

    Calculating subtransient fault currents for three-phase faults in an N-bus power system involves using the positive-sequence network. When a three-phase short circuit occurs at a specific bus, the analysis uses the superposition method to evaluate two separate circuits.
    In the first circuit, all machine voltage sources are short-circuited, leaving only the prefault voltage source at the fault location. The positive-sequence bus impedance matrix can be determined by solving the nodal equations,...
    582