Related Experiment Video

Updated: Apr 6, 2026

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material
07:42

Quasistatic Mechanical Testing for Computer-Aided Design and Manufacturing Occlusal Veneers Cemented to Milled Dentin Analog Material

Published on: December 20, 2024

950

Influence of the bracket on bonding and physical behavior of orthodontic resin cements

Victoria Bolaños-Carmona1, Bilal Zein, Mario Menéndez-Núñez

  • 1Department of Stomatology, Campus de Cartuja, University of Granada.

Dental Materials Journal
|August 4, 2015
PubMed

More Related Videos

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires08:46

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires

Published on: July 24, 2018

11.4K
Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation08:45

Shrinkage of Dental Composite in Simulated Cavity Measured with Digital Image Correlation

Published on: July 21, 2014

14.1K

Related Concept Videos

Bonding and Strength of Aggregate01:12

Bonding and Strength of Aggregate

The bond between aggregate particles and the cement matrix is significantly influenced by the shape and surface texture of the aggregates. High-strength concretes benefit from a rougher texture, which leads to stronger bonding due to greater adhesion. Angular aggregates with larger surface areas also enhance this bond. The bonding quality, however, is complex to assess as no universally accepted test exists. Good bonding is indicated when a crushed concrete specimen shows some aggregate...
977
Strength and Heat of Hydration01:29

Strength and Heat of Hydration

The hydration of cement is an exothermic reaction in which heat is generated as cement hydrates. This heat of hydration is critical to cement's strength development. The rate at which this heat is generated affects the temperature rise, with a majority of the heat being released early in the hydration process, half within the first three days, and about 75% within the first week.
The heat of hydration for each cement compound is significant; for instance, tricalcium aluminate (C3A) and...
856
Mortar Properties01:17

Mortar Properties

Mortar properties encompass a range of characteristics crucial for construction and masonry work, including workability, water retention, bond strength, durability, compressive strength, volume change, and appearance. Workability refers to mortar's ability to be easily applied and manipulated without sagging or falling off surfaces, which is important for efficient masonry unit placement and alignment. Water retention is essential to prevent the mortar from losing moisture too quickly to...
613
Strength of Cement01:20

Strength of Cement

Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
774
Brick Masonry01:12

Brick Masonry

Brick masonry uses bricks as the building blocks and involves building walls from individual bricks laid in mortar. The basic building block of brick masonry is the wythe, a vertical layer of bricks with a thickness of one brick. Within a wythe, bricks can be laid in various courses or patterns, with the most common being the stretcher course, where bricks are laid with their long edge horizontal and face parallel to the wall.
For thicker walls, multiple wythes are bonded together using...
686
Complexation Equilibria: Factors Influencing Stability of Complexes01:09

Complexation Equilibria: Factors Influencing Stability of Complexes

In complexation reactions, metal cations are the electron pair acceptors, and the ligands are the electron pair donors. The stability of the metal complexes depends primarily on the complexing ability of the central metal ion and the nature of the ligands. Generally, the complexing ability of the metal ion depends on the size and charge of the ion. As the metal ion size increases, the stability of the metal complexes decreases, provided that the valency of the metal ion and the ligands remain...
972