Related Experiment Video

Updated: Apr 4, 2026

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit
05:30

Large Scale Energy Efficient Sensor Network Routing Using a Quantum Processor Unit

Published on: September 8, 2023

1.2K

Generalized Kirchhoff-Law-Johnson-Noise (KLJN) secure key exchange system using arbitrary resistors

Gergely Vadai1, Robert Mingesz1, Zoltan Gingl1

  • 1Department of Technical Informatics, University of Szeged, Hungary.

Scientific Reports
|September 4, 2015
PubMed

More Related Videos

Fabrication and Validation of an Organ-on-chip System with Integrated Electrodes to Directly Quantify Transendothelial Electrical Resistance10:51

Fabrication and Validation of an Organ-on-chip System with Integrated Electrodes to Directly Quantify Transendothelial Electrical Resistance

Published on: September 26, 2017

17.3K
Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface11:54

Real-Time Proxy-Control of Re-Parameterized Peripheral Signals using a Close-Loop Interface

Published on: May 8, 2021

5.3K

Related Concept Videos

Combination Of Resistors01:18

Combination Of Resistors

Electrical devices in any circuit can be connected either by series or parallel connections. Additionally, circuits can be connected involving both of these connections, known as combination or complex circuits. As these circuits have complex resistor connections, it is necessary to identify different parts as either series or parallel connections, then the whole combination of series and parallel resistors can be reduced to a single equivalent resistance. With the known equivalent resistance...
4.4K
Resistors In Parallel01:23

Resistors In Parallel

Resistors are in parallel when one end of all the resistors are connected to a continuous wire of negligible resistance and the other end of all the resistors are also connected to one another through a continuous wire of negligible resistance. In the case of a parallel configuration, the potential drop across each resistor is the same. Current through each resistor can be found using Ohm’s law, I = V/R, where the voltage is constant across each resistor. The sum of the individual currents...
7.1K
Equivalent Resistance01:16

Equivalent Resistance

In circuit analysis, situations often arise where resistors are neither in series nor parallel configurations. To tackle such scenarios, three-terminal equivalent networks like the wye (Y) (Figure 1 (a)) or tee (T) and delta (Δ) (Figure 1 (b)) or pi (π) networks come into play. These networks offer versatile solutions and are frequently encountered in various applications, including three-phase electrical systems, electrical filters, and matching networks.
1.2K
Norton Equivalent Circuits01:16

Norton Equivalent Circuits

Norton's theorem is a fundamental concept in the field of electrical engineering that allows for the simplification of complex AC circuits. The theorem states that any two-terminal linear network can be replaced with an equivalent circuit that consists of an impedance, which is parallel with a constant current source. Figure 1 shows the AC circuit portioned into two parts: Circuit A and Circuit B, while Figure 2 depicts the circuit obtained by replacing Circuit A by its Norton equivalent...
955
Resistors In Series01:10

Resistors In Series

A resistor is an ohmic device that limits the flow of charge in a circuit. Most circuits have more than one resistor. If several resistors are connected together and connected to a battery, the current supplied by the battery depends on the equivalent resistance of the circuit. The equivalent resistance of a combination of resistors depends on both their individual values and how they are connected. The simplest combination of resistors is the series combination. 
In a series circuit, the...
7.5K
Norton's Theorem01:14

Norton's Theorem

Norton's theorem is a fundamental principle stating that a linear two-terminal circuit can be substituted with an equivalent circuit, which comprises a current source (ⅠN) in parallel with a resistor (RN). Here, ⅠN represents the short-circuit current flowing through the terminals, and RN stands for the input or equivalent resistance at the terminals when all independent sources are deactivated. This implies that the circuit illustrated in Figure (a) can be exchanged with the one depicted...
1.9K