Related Experiment Video

Updated: Mar 31, 2026

Surface Properties of Synthesized Nanoporous Carbon and Silica Matrices
09:31

Surface Properties of Synthesized Nanoporous Carbon and Silica Matrices

Published on: March 27, 2019

10.1K

Observation of residual disorder in the centre of amorphous solid water films after pore collapse at 125 K

S Townrow1, P G Coleman1

  • 1Department of Physics, University of Bath, Bath BA2 7AY, UK.

Journal of Physics. Condensed Matter : an Institute of Physics Journal
|October 31, 2015
PubMed

More Related Videos

Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography08:02

Reservoir Condition Pore-scale Imaging of Multiple Fluid Phases Using X-ray Microtomography

Published on: February 25, 2015

13.2K
Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package06:37

Analyzing Melts and Fluids from Ab Initio Molecular Dynamics Simulations with the UMD Package

Published on: September 17, 2021

5.2K

Related Concept Videos

Polymer Classification: Crystallinity01:21

Polymer Classification: Crystallinity

Unlike ionic or small covalent molecules, polymers do not form crystalline solids due to the diffusion limitations of their long-chain structures. However, polymers contain microscopic crystalline domains separated by amorphous domains.
Crystalline domains are the regions where polymer chains are aligned in an orderly manner and held together in proximity by intermolecular forces. For example, chains in the crystalline domains of polyethylene and nylon are bound together by van der Waals...
4.2K
States of Water01:23

States of Water

Water exists in any one of the three classical states: solid (ice), liquid (water), and gas (steam or water vapor). The state of water depends on i) the intermolecular forces that draw molecules together and ii) the kinetic energy that leads to movements that pull them apart.
Water freezes when the intermolecular forces are greater than the kinetic energy. Unlike most other substances, water is less dense in its solid state than in its liquid state. This is because each water molecule can form...
58.3K
Entropy and Solvation02:05

Entropy and Solvation

The process of surrounding a solute with solvent is called solvation. It involves evenly distributing the solute within the solvent. The rule of thumb for determining a solvent for a given compound is that like dissolves like. A good solvent has molecular characteristics similar to those of the compound to be dissolved. For example, polar solutions dissolve polar solutes, and apolar solvents dissolve apolar solutes. A polar solvent is a solvent that has a high dielectric constant (ϵ...
8.7K
Phase Transitions: Vaporization and Condensation02:39

Phase Transitions: Vaporization and Condensation

The physical form of a substance changes on changing its temperature. For example, raising the temperature of a liquid causes the liquid to vaporize (convert into vapor). The process is called vaporization—a surface phenomenon. Vaporization occurs when the thermal motion of the molecules overcome the intermolecular forces, and the molecules (at the surface) escape into the gaseous state. When a liquid vaporizes in a closed container, gas molecules cannot escape. As these gas phase molecules...
22.1K
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
4.7K
Theories of Dissolution: The Danckwerts' Model and Interfacial Barrier Model01:09

Theories of Dissolution: The Danckwerts' Model and Interfacial Barrier Model

Various dissolution theories provide insight into the factors that influence the dissolution rate. Danckwerts' Model suggests that turbulence, rather than a stagnant layer, characterizes the dissolution medium at the solid-liquid interface. In this model, the agitated solvent contains macroscopic packets that move to the interface via eddy currents, facilitating the absorption and delivery of the drug to the bulk solution. The regular replenishment of solvent packets maintains the...
911