Related Experiment Video

Updated: Mar 30, 2026

Laboratory Estimation of Net Trophic Transfer Efficiencies of PCB Congeners to Lake Trout Salvelinus namaycush from Its Prey
12:24

Laboratory Estimation of Net Trophic Transfer Efficiencies of PCB Congeners to Lake Trout Salvelinus namaycush from Its Prey

Published on: August 29, 2014

11.4K

Isahaya Bay, freshwater lake to an estuary again

Yuichi Hayami1, Takaharu Hamada1

  • 1Institute of Lowland and Marine Research, Saga University, 840-8502 Saga, Japan.

Marine Pollution Bulletin
|November 5, 2015
PubMed

Keywords:
Ariake SeaIsahaya BayNumerical simulationReclamationSea water reintroductionSediment transport

More Related Videos

A New Clarification Method to Visualize Biliary Degeneration During Liver Metamorphosis in Sea Lamprey Petromyzon marinus07:03

A New Clarification Method to Visualize Biliary Degeneration During Liver Metamorphosis in Sea Lamprey Petromyzon marinus

Published on: June 6, 2014

14.3K
Author Spotlight: Unveiling Plankton Response to Climate Change Through Time-Series Data and Artistic Expression08:15

Author Spotlight: Unveiling Plankton Response to Climate Change Through Time-Series Data and Artistic Expression

Published on: July 28, 2023

2.0K

Related Concept Videos

Freshwater Microbial Ecology01:24

Freshwater Microbial Ecology

Freshwater systems such as streams, rivers, and lakes exhibit distinct physical and biological characteristics that influence their microbial communities. These environments are broadly categorized into lotic systems—those with flowing waters like streams and most rivers—and lentic systems, which include still or slow-moving waters such as lakes, ponds, and marshes.In lentic systems, phytoplankton drive primary production, generating autochthonous organic carbon. In contrast, lotic...
38
Osmoregulation in Fishes02:32

Osmoregulation in Fishes

When cells are placed in a hypotonic (low-salt) fluid, they can swell and burst. Meanwhile, cells in a hypertonic solution—with a higher salt concentration—can shrivel and die. How do fish cells avoid these gruesome fates in hypotonic freshwater or hypertonic seawater environments?
55.0K
Quality of Water01:19

Quality of Water

In concrete preparation, the quality of water is paramount as it affects the strength and durability of the concrete. Potable water is usually preferred; however, it must not have excessive sodium or potassium to prevent compromising the concrete's integrity. Water quality is typically evaluated based on impurities such as dissolved solids, chlorides, and sulfates, and its pH value is ideally between 6 and 8. Even slightly acidic natural water may be acceptable unless it contains harmful...
679
States of Water01:23

States of Water

Water exists in any one of the three classical states: solid (ice), liquid (water), and gas (steam or water vapor). The state of water depends on i) the intermolecular forces that draw molecules together and ii) the kinetic energy that leads to movements that pull them apart.
Water freezes when the intermolecular forces are greater than the kinetic energy. Unlike most other substances, water is less dense in its solid state than in its liquid state. This is because each water molecule can form...
58.3K
Effect of Sea Water on Concrete01:22

Effect of Sea Water on Concrete

Concrete exposed to seawater can undergo degradation like the dissolution of ettringite and gypsum, increasing the material's porosity and decreasing its strength. In contrast, the crystallization of salts within the concrete's pores can cause expansion, particularly above the waterline where evaporation occurs. Nonetheless, this expansion only happens when seawater, enabled by the concrete's permeability, manages to infiltrate the structure.
Concrete in areas between tide marks,...
1.3K
Testing Water Quality01:14

Testing Water Quality

When the quality of water for concrete preparation is uncertain, its impact on the setting time of cement and compressive strength of mortar is assessed by comparison with de-ionized or distilled water benchmarks. American Society for Testing and Materials (ASTM) C1602 requires the setting times to be within 90 minutes of the control, British Standard (BS) 3146:1980 allows a 30-minute variance in the initial setting, while British Standards European Norm (BS EN) 1008 specifies initial setting...
526