Related Experiment Video

Updated: Mar 26, 2026

Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces
09:33

Demonstration of Equal-Intensity Beam Generation by Dielectric Metasurfaces

Published on: June 7, 2019

6.8K

25-Gb/s broadband silicon modulator with 0.31-V·cm VπL based on forward-biased PIN diodes embedded with passive

Takeshi Baba, Suguru Akiyama, Masahiko Imai

    Optics Express
    |February 3, 2016
    PubMed

    More Related Videos

    Multiplex Chemical Imaging Based on Broadband Stimulated Raman Scattering Microscopy09:57

    Multiplex Chemical Imaging Based on Broadband Stimulated Raman Scattering Microscopy

    Published on: July 25, 2022

    4.7K
    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis07:55

    High-speed Continuous-wave Stimulated Brillouin Scattering Spectrometer for Material Analysis

    Published on: September 22, 2017

    10.8K

    Related Concept Videos

    Diode: Forward bias01:20

    Diode: Forward bias

    In semiconductor devices, diodes play a crucial role in directing current flow, and its operation is primarily categorized into forward bias and reverse bias. A diode is said to be forward-biased when its p-type region is connected to the positive terminal of a battery and its n-type region is linked to the negative terminal. This configuration reduces the potential barrier within the diode, allowing current to flow easily from the p to the n-type region.
    The behavior of a diode in forward bias...
    2.8K
    MOSFET Amplifiers01:17

    MOSFET Amplifiers

    The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
    658
    Biasing of P-N Junction01:16

    Biasing of P-N Junction

    The operation of a p-n junction diode involves various biasing conditions, including forward bias, reverse bias, and equilibrium.
    In equilibrium, no external voltage is applied across the p-n junction. The depletion region is formed at the junction interface due to the diffusion of carriers, which leaves behind charged dopants, acceptors on the p-side, and donors on the n-side. These immobile charges create an electric field that prevents further diffusion of carriers. The related energy band...
    2.5K
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    804
    Biasing of FET01:22

    Biasing of FET

    Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
    In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
    907
    Small-Signal Analysis of MOSFET Amplifiers01:23

    Small-Signal Analysis of MOSFET Amplifiers

    In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
    1.3K