Divided-pulse amplification to the joule level

Related Experiment Video

Updated: Mar 18, 2026

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier
10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

12.1K

Benjamin Webb, Ahmad Azim, Nathan Bodnar

    Optics Letters
    |July 2, 2016
    PubMed

    More Related Videos

    Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping14:58

    Silicon Metal-oxide-semiconductor Quantum Dots for Single-electron Pumping

    Published on: June 3, 2015

    15.5K
    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference07:56

    A Photonic System for Generating Unconditional Polarization-Entangled Photons Based on Multiple Quantum Interference

    Published on: September 5, 2019

    9.1K

    Related Concept Videos

    Joule-Thomson Effect01:21

    Joule-Thomson Effect

    The Joule-Thomson effect, also known as the Joule-Kelvin effect, describes the temperature change of a fluid when it is forced through a valve or porous plug while keeping it in a thermally insulated environment. This experiment is called a throttling process. This is an important effect widely used in refrigeration and the liquefaction of gases.
    This experiment forces high-pressure gas through a throttle valve or a porous plug to a lower-pressure region. The gas expands as it passes through to...
    10.9K
    Amplifying Signals via Enzymatic Cascade01:22

    Amplifying Signals via Enzymatic Cascade

    When a ligand binds to a cell-surface receptor, the receptor's intracellular domain changes shape, which may either activate its enzyme function or allow its binding to other molecules. The initial signal is amplified by most signal transduction pathways. This means that a single ligand molecule can activate multiple molecules of a downstream target. Proteins that relay a signal are most commonly phosphorylated at one or more sites, activating or inactivating the protein. Kinases catalyze...
    19.0K
    The Joule and Joule–Thomson Experiments01:23

    The Joule and Joule–Thomson Experiments

    Consider an adiabatic system composed of two chambers, A and B, designed such that no heat flows into or out of the system. Initially, chamber A is filled with a gas at a fixed temperature T1, pressure p1, and volume V1, while chamber B is evacuated. The gas is then gradually forced through a rigid, porous barrier to chamber B, ultimately reaching temperature T2, pressure p2, and volume V2. A piston on the right side maintains a constant pressure (p2), which is lower than p1. The significant...
    84
    Maximum Power Transfer01:16

    Maximum Power Transfer

    Numerous practical applications within engineering disciplines, such as telecommunications, necessitate optimizing power delivery to a connected load. This pursuit, however, entails inherent internal losses, which can either equal or exceed the power supplied to the load. The Thevenin equivalent circuit is helpful in finding the maximum power a linear circuit can deliver to a load. It is assumed in this context that the load resistance can be adjusted.
    By substituting the entire circuit with...
    1.1K
    Voltage Dividers01:14

    Voltage Dividers

    In electrical circuits, resistors can be connected in series, sequentially linked one after the other. In a series configuration, the same current flows through each resistor. Ohm's law is a fundamental principle to understand the behavior of resistors in series. It expresses the voltage across these resistors in terms of the current and resistance.
    Kirchhoff's voltage law implies that the sum of the voltages across the resistors in series equals the source voltage. This means that the current...
    1.6K
    Voltage Doubler Circuit01:23

    Voltage Doubler Circuit

    A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
    2.0K