Related Experiment Video

Updated: Mar 17, 2026

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle
14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

14.5K

Effect of Assembly Stresses on Fatigue Life of Symmetrical 65Si7 Leaf Springs

Vinkel Kumar Arora1, Gian Bhushan2, M L Aggarwal3

  • 1Department of Mechanical Engineering, ITM University, Sector 23A, Gurgaon, Haryana 122017, India.

International Scholarly Research Notices
|July 20, 2016
PubMed

More Related Videos

Ultrasonic Fatigue Testing in the Tension-Compression Mode06:54

Ultrasonic Fatigue Testing in the Tension-Compression Mode

Published on: March 7, 2018

11.3K
Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method07:37

Full-field Strain Measurements for Microstructurally Small Fatigue Crack Propagation Using Digital Image Correlation Method

Published on: January 16, 2019

10.2K

Related Concept Videos

Euler's Formula to Columns: Problem Solving01:23

Euler's Formula to Columns: Problem Solving

Euler's formula is used in structural engineering to determine the buckling load of columns under various conditions. However, when dealing with systems that incorporate both rigid elements and elastic components, such as springs, the analysis requires a finer approach to determine the critical load. The problem described involves two rigid bars connected at a pivot point with a spring attached and a vertical load applied at one end.
The system comprises two vertical rigid bars, AB and BC, of...
1.1K
Fatigue01:21

Fatigue

Fatigue occurs when materials rupture under repeated or fluctuating loads, even at stress levels far below their static breaking strength. It typically results in brittle failure, even for ductile materials. It is a critical consideration in designing machines and structural components subjected to repetitive or varying loads. The nature of these loadings can range from fluctuating loads like unbalanced pump impellers causing vibrations to repeatedly bending a thin steel rod wire back and forth...
978
Stresses under Combined Loadings01:23

Stresses under Combined Loadings

When analyzing a bent tube with a circular cross-section subjected to multiple forces, it is crucial to determine the stress distribution in order to maintain structural integrity under varied load conditions.
The process begins by slicing the tube at critical points and analyzing the internal forces and stress components at these sections, focusing on the centroid. Normal stresses, generated by axial forces and bending moments, are either compressive or tensile and vary across the section from...
523
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
628
Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
777
Stress: General Loading Conditions01:15

Stress: General Loading Conditions

To grasp the intricacy of real-world conditions where multiple loads are applied simultaneously to a structure, one might visualize a section passing through a specific point within a body, aligned parallel to the xy plane. This section is subjected to various forces, including original loads, normal forces, and shearing forces.
The shearing force, possessing potential directionality within the plane of the section, is simplified into two component forces running parallel to the x and y axes....
655