Related Experiment Video

Updated: Mar 12, 2026

Individualized Stem-positioning in Calcar-guided Short-stem Total Hip Arthroplasty
09:31

Individualized Stem-positioning in Calcar-guided Short-stem Total Hip Arthroplasty

Published on: February 27, 2018

12.6K

Windswept deformities - An indication to individualise valgus correction angle during total knee arthroplasty

Gautam M Shetty1, Arun Mullaji1, Ahmed Adel Khalifa1

  • 1Breach Candy Hospital & Mullaji Knee Clinic, Mumbai, India.

Journal of Orthopaedics
|November 11, 2016
PubMed
Abstract

Keywords:
KneeOsteoarthritisTotal knee arthroplastyWindswept

More Related Videos

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy08:15

Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy

Published on: February 17, 2023

1.5K
Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach09:01

Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach

Published on: January 24, 2018

12.5K

Related Concept Videos

Unsymmetric Bending - Angle of Neutral Axis01:15

Unsymmetric Bending - Angle of Neutral Axis

Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
946
Angle of Twist - Elastic Range01:13

Angle of Twist - Elastic Range

Consider a cylindrical shaft with a length denoted by L and a consistent cross-sectional radius referred to as r. This shaft undergoes a torque at the free end. The highest shearing strain within the shaft is directly proportional to the twist angle and the radial distance from the shaft axis. When the shaft behaves elastically, this shearing strain can be articulated using variables such as the applied torque, radial distance, the polar moment of inertia, and the modulus of rigidity. By...
874
Knee Joint01:23

Knee Joint

The knee joint is the most complicated joint in the body. It consists of three articulations– two tibiofemoral and one patellofemoral. As is characteristic of synovial joints, the knee joint has a thin articular capsule that partially surrounds this joint cavity. Additionally, several ligaments, muscles, and cartilaginous structures support the movement of the knee.
A total of seven ligaments support the knee joint. The patellar ligament, which is also attached to the quadriceps femoris...
3.6K
Angle of Twist: Problem Solving01:13

Angle of Twist: Problem Solving

An electric motor applies a torque of 700 N·m to an aluminum shaft, triggering a stable rotation. Two pulleys, B and C, are subjected to torques of 300 N·m and 400 N·m, respectively. The modulus of rigidity is provided as 25 GPa. With the knowledge of the length and diameter of each segment, the twist angle between the two pulleys can be computed. First, a section cut is made between pulleys B and C, and the cut cross-section is analyzed using a free-body diagram. Given that the torque...
841
Ankle Joint01:10

Ankle Joint

The ankle is formed by the talocrural joint (crural = leg). It consists of the articulations between the talus bone of the foot and the distal ends of the tibia and fibula of the leg. The superior aspect of the talus bone is square-shaped and has three areas of articulation. The top of the talus articulates with the inferior tibia. This is the portion of the ankle joint that carries the body weight between the leg and foot. The sides of the talus are firmly held in position by the articulations...
3.3K