Related Experiment Video

Updated: Mar 10, 2026

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine
08:16

Ice Generation and the Heat and Mass Transfer Phenomena of Introducing Water to a Cold Bath of Brine

Published on: March 13, 2017

14.6K

Solidification of supercooled water in the vicinity of a solid wall

Markus Schremb1, Cameron Tropea1

  • 1Institute of Fluid Mechanics and Aerodynamics, Technische Universität Darmstadt, 64289 Darmstadt, Germany.

Physical Review. E
|December 15, 2016
PubMed

More Related Videos

A Microfluidic Approach for the Study of Ice and Clathrate Hydrate Crystallization08:01

A Microfluidic Approach for the Study of Ice and Clathrate Hydrate Crystallization

Published on: August 18, 2022

3.6K
Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications11:20

Fabrication of Superhydrophobic Metal Surfaces for Anti-Icing Applications

Published on: August 15, 2018

9.0K

Related Concept Videos

Solid–Solid Solutions01:24

Solid–Solid Solutions

The temperature-composition phase diagram of two solids, A and B, which are immiscible in the solid phase but form miscible liquids, shows that when the temperature is low, these two exist as separate, pure solids (A and B). As the temperature increases, they transition into a single-phase liquid solution where A and B coexist. Moving from point a1 to a2 in the phase diagram, the composition changes such that solid B begins to separate from the solution, enriching the remaining liquid with A.
34
Phase Transitions: Melting and Freezing02:39

Phase Transitions: Melting and Freezing

Heating a crystalline solid increases the average energy of its atoms, molecules, or ions, and the solid gets hotter. At some point, the added energy becomes large enough to partially overcome the forces holding the molecules or ions of the solid in their fixed positions, and the solid begins the process of transitioning to the liquid state or melting. At this point, the temperature of the solid stops rising, despite the continual input of heat, and it remains constant until all of the solid is...
15.4K
States of Water01:23

States of Water

Water exists in any one of the three classical states: solid (ice), liquid (water), and gas (steam or water vapor). The state of water depends on i) the intermolecular forces that draw molecules together and ii) the kinetic energy that leads to movements that pull them apart.
Water freezes when the intermolecular forces are greater than the kinetic energy. Unlike most other substances, water is less dense in its solid state than in its liquid state. This is because each water molecule can form...
57.9K
Recrystallization: Solid–Solution Equilibria01:10

Recrystallization: Solid–Solution Equilibria

Recrystallization is a purification technique used to separate impurities from solid compounds. In this technique, no chemical reactions occur. Instead, it exploits physical properties only, specifically, the solubility differences between the desired compound and impurities, either at a single temperature or at different temperatures, and under other selected conditions. The solid-solution equilibrium (solubility equilibrium) of each component in the solution represents a binary phase...
4.2K
Phase Diagrams02:39

Phase Diagrams

A phase diagram combines plots of pressure versus temperature for the liquid-gas, solid-liquid, and solid-gas phase-transition equilibria of a substance. These diagrams indicate the physical states that exist under specific conditions of pressure and temperature and also provide the pressure dependence of the phase-transition temperatures (melting points, sublimation points, boiling points). Regions or areas labeled solid, liquid, and gas represent single phases, while lines or curves represent...
51.0K
Liquid–Solid Solutions01:29

Liquid–Solid Solutions

The process of a solid dissolving in a liquid to form a solution is governed by the solubility limit, which is the maximum amount of the solid substance, or solute, that can be dissolved in a specific volume of the liquid or solvent. As the solute dissolves, it reaches a point where no more solute can be dissolved at a given temperature - this is known as the saturation point. However, if further solute is added and it manages to dissolve, the solution becomes supersaturated. Supersaturated...
36