Predicting the transmissibility of a suspension seat

Related Experiment Video

Updated: Mar 8, 2026

The Tail Suspension Test
10:17

The Tail Suspension Test

Published on: January 28, 2012

83.8K

Thomas E Fairley1

  • 1a Institut National de Recherche et de Sécurité-Centre de Recherche , Avenue de Bourgogne, B.P. No. 27, 54501 , Vandoeuvre Cedex , France.

Ergonomics
|January 13, 2017
PubMed

Keywords:
SeatsWhole-body vibration

More Related Videos

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle14:57

Structural Design and Manufacturing of a Cruiser Class Solar Vehicle

Published on: January 30, 2019

14.5K
Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research07:15

Tactile Vibrating Toolkit and Driving Simulation Platform for Driving-Related Research

Published on: December 18, 2020

5.1K

Related Concept Videos

Design of Transmission Shafts - Stress Analysis01:15

Design of Transmission Shafts - Stress Analysis

Designing a transmission shaft requires a thorough understanding of the stresses induced by bending moments and torques, especially in systems where power is transferred through gears. These forces create force-couple systems at the centers of the shaft's cross-sections, leading to both transverse and torsional loading. Although shearing stresses from transverse loads are typically smaller than those from torques and are often overlooked, the significant normal stresses from these loads...
768
Normal and Tangetial Components: Problem Solving01:24

Normal and Tangetial Components: Problem Solving

Consider a man with a mass of 70 kg seated in a chair connected to a pin support through a member BC. If the man maintains an upright position, the task is to determine the horizontal and vertical reactions of the chair on the man when the member makes a 45° angle with the horizontal. At this moment, the man has a speed of 5 m/s, increasing at a rate of 1 m/s².
646
Design of Transmission Shafts01:16

Design of Transmission Shafts

The design of a transmission shaft is governed by two primary specifications: the power it transmits and its rotational speed. These parameters guide the selection of the shaft's material and cross-sectional dimensions, ensuring that the material's maximum shearing stress remains within the elastic limit while transmitting the desired power at the given speed. The system's power is intrinsically linked to the applied torque. The torque applied to the shaft can be calculated by reconfiguring the...
849
Transmission Shafts: Problem Solving01:09

Transmission Shafts: Problem Solving

Designing a solid shaft that transmits power from a motor to a machine tool involves a series of calculations to ensure the shaft can withstand the stresses applied by bending moments and torques. First, calculate the torque exerted on the gear, considering the power transmitted by the shaft and its rotational speed. Following this, compute the tangential forces acting on the gears, which directly relate to the torque and the gear radius.
Next, use bending moment diagrams for the shaft to...
545
PD Controller: Design01:26

PD Controller: Design

In automotive engineering, car suspension systems often employ Proportional Derivative (PD) controllers to enhance performance. PD controllers are utilized to adjust the damping force in response to road conditions. A controller, acting as an amplifier with a constant gain, demonstrates proportional control, with output directly mirroring input.
Designing a continuous-data controller requires selecting and linking components like adders and integrators, which are fundamental in Proportional,...
688
Friction: Problem Solving01:21

Friction: Problem Solving

Friction is an essential force that influences the motion of objects in daily life. Depending on the situation, it can be either beneficial or problematic. Consider a bus with a mass of three megagrams and its center of mass at a specific point, moving along a banked road at a constant speed. The coefficient of static friction between the tires and the road is 0.5. Find the maximum angle of the banked road at which the bus would not slip or tip.
Initially, a visual representation of the...
568