Related Experiment Video

Updated: May 16, 2026

Measurement of Scattering Nonlinearities from a Single Plasmonic Nanoparticle
15:06

Measurement of Scattering Nonlinearities from a Single Plasmonic Nanoparticle

Published on: January 3, 2016

13.5K

The Optical Society's 2016 topical meeting on optical interference coatings: introduction

Detlev Ristau, Li Li, Robert Sargent

    Applied Optics
    |February 4, 2017
    PubMed

    More Related Videos

    Measuring Magnetically-Tuned Ferroelectric Polarization in Liquid Crystals07:03

    Measuring Magnetically-Tuned Ferroelectric Polarization in Liquid Crystals

    Published on: August 15, 2018

    9.3K
    High-Accuracy Correction of 3D Chromatic Shifts in the Age of Super-Resolution Biological Imaging Using Chromagnon08:18

    High-Accuracy Correction of 3D Chromatic Shifts in the Age of Super-Resolution Biological Imaging Using Chromagnon

    Published on: June 16, 2020

    8.0K

    Related Concept Videos

    Interference and Diffraction02:18

    Interference and Diffraction

    Interference is a characteristic phenomenon exhibited by waves. When two electromagnetic waves interact with their peaks and troughs coinciding, a resulting wave with enhanced amplitude is produced. This is known as constructive interference. In this case, the two waves interacting are in phase with each other.
    Imaging Biological Samples with Optical Microscopy01:18

    Imaging Biological Samples with Optical Microscopy

    Optical microscopy uses optic principles to provide detailed images of samples. Antonie van Leeuwenhoek designed the first compound optical microscope in the 17th century to visualize blood cells, bacteria, and yeast cells. In 1830, Joseph Jackson Lister created an essentially modern light microscope. The 20th century saw the development of microscopes with enhanced magnification and resolution.
    In optical microscopy, the specimen to be viewed is placed on a glass slide and clipped on the stage...
    Confocal Fluorescence Microscopy01:16

    Confocal Fluorescence Microscopy

    Confocal microscopy is an advanced microscopic technique. The prime advantage of the confocal microscope over other microscopy techniques is its ability to block the out-of-focus light from the illuminated samples using pinholes. It is widely used with fluorescence optics to obtain high-resolution, sharp contrast images. Unlike optical microscopes, confocal microscopes use a focused beam of light laser to scan the entire sample surface at different z-planes. These microscopes are, therefore,...
    Total Internal Reflection Fluorescence Microscopy01:05

    Total Internal Reflection Fluorescence Microscopy

    Total internal reflection fluorescence microscopy or TIRF is an advanced microscopic technique used to visualize fluorophores in samples close to a solid surface with a higher refractive index, such as a glass coverslip. TIRF only allows fluorophores in proximity to the solid surface to be excited. When light from a medium with a lower refractive index (such as air) hits the glass coverslip at a critical angle, the light undergoes total internal reflection stead of passing through the glass.
    Atomic Absorption Spectroscopy: Interference01:25

    Atomic Absorption Spectroscopy: Interference

    Interference leads to systematic error in atomic absorption (AA) measurements by enhancing or diminishing the analytical signal or the background. These interferences can be grouped into three main categories: spectral interference, chemical interference, and physical interference.
    Spectral interference occurs when signals from other elements or molecules overlap with the analyte signal, falsely elevating or masking the analyte's absorbance. This interference can be corrected using Zeeman,...
    Atomic Emission Spectroscopy: Interference01:30

    Atomic Emission Spectroscopy: Interference

    In atomic emission spectroscopy (AES), high-temperature atomizers excite a broad range of elements and molecules that generate complex emissions from sources such as oxides, hydroxides, and flame combustion products in the flame or plasma. Several strategies can be employed to minimize spectral interferences caused by overlapping emission lines or bands. These include increasing instrument resolution, choosing alternative emission lines, optimally placing the detector in low-background regions,...