Related Experiment Video

Updated: Mar 7, 2026

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar
07:14

Tracking Infiltration Front Depth Using Time-lapse Multi-offset Gathers Collected with Array Antenna Ground Penetrating Radar

Published on: May 1, 2018

8.2K

On the limits of digital back-propagation in the presence of transceiver noise

Lidia Galdino, Daniel Semrau, Domaniç Lavery

    Optics Express
    |March 1, 2017
    PubMed

    More Related Videos

    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements09:36

    Continuous-Wave Propagation Channel-Sounding Measurement System - Testing, Verification, and Measurements

    Published on: June 25, 2021

    3.6K
    Continuous Measurement of Biological Noise in Escherichia Coli Using Time-lapse Microscopy08:25

    Continuous Measurement of Biological Noise in Escherichia Coli Using Time-lapse Microscopy

    Published on: April 27, 2021

    4.2K

    Related Concept Videos

    Propagation Speed of Electromagnetic Waves01:30

    Propagation Speed of Electromagnetic Waves

    Electromagnetic waves are consistent with Ampere's law. Assuming there is no conduction current Ampere's law is given as:
    4.8K
    Difference from Background: Limit of Detection01:05

    Difference from Background: Limit of Detection

    The limit of detection (LOD) is the smallest amount of analyte that can be distinguished from the background noise. The LOD value corresponds to the concentration at which the analyte signal is three times larger than the standard deviation of the blank signal. Below this value, the analyte signal cannot be differentiated from the background noise. It is calculated by dividing the calibration slope by 3 times the standard deviation of the blank signals.
    The LOD indicates the presence or absence...
    8.7K
    Propagation of Uncertainty from Random Error00:59

    Propagation of Uncertainty from Random Error

    An experiment often consists of more than a single step. In this case, measurements at each step give rise to uncertainty. Because the measurements occur in successive steps, the uncertainty in one step necessarily contributes to that in the subsequent step. As we perform statistical analysis on these types of experiments, we must learn to account for the propagation of uncertainty from one step to the next. The propagation of uncertainty depends on the type of arithmetic operation performed on...
    2.1K
    Propagation of Uncertainty from Systematic Error01:10

    Propagation of Uncertainty from Systematic Error

    The atomic mass of an element varies due to the relative ratio of its isotopes. A sample's relative proportion of oxygen isotopes influences its average atomic mass. For instance, if we were to measure the atomic mass of oxygen from a sample, the mass would be a weighted average of the isotopic masses of oxygen in that sample. Since a single sample is not likely to perfectly reflect the true atomic mass of oxygen for all the molecules of oxygen on Earth, the mass we obtain from this...
    1.5K
    Boundary Conditions: Lossless Lines01:21

    Boundary Conditions: Lossless Lines

    Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
    At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
    449
    Diode: Reverse bias01:14

    Diode: Reverse bias

    A diode is reverse-biased when the positive terminal of an external voltage source is connected to the n-type material and the negative terminal to the p-type material. This configuration opposes the natural direction of current flow through the diode, effectively increasing the width of the depletion region and the barrier potential. The reverse bias condition produces a minimal leakage current, primarily due to minority charge carriers. This leakage becomes significant when the reverse...
    2.3K