Related Experiment Video

Updated: Mar 6, 2026

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators
09:23

Quantum State Engineering of Light with Continuous-wave Optical Parametric Oscillators

Published on: May 30, 2014

15.1K

Multi-mode of Four and Six Wave Parametric Amplified Process

Dayu Zhu1, Yiheng Yang1, Da Zhang1

  • 1Key Laboratory for Physical Electronics and Devices of the Ministry of Education &Shaanxi Key Lab of Information Photonic Technique, Xi'an Jiaotong University, Xi'an 710049, China.

Scientific Reports
|March 4, 2017
PubMed

More Related Videos

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier10:17

20 mJ, 1 ps Yb:YAG Thin-disk Regenerative Amplifier

Published on: July 12, 2017

12.1K
Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping09:43

Transmission of Multiple Signals through an Optical Fiber Using Wavefront Shaping

Published on: March 20, 2017

10.4K

Related Concept Videos

Cascaded Op Amps01:16

Cascaded Op Amps

Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
1.2K
Amplifying Signals via Enzymatic Cascade01:22

Amplifying Signals via Enzymatic Cascade

When a ligand binds to a cell-surface receptor, the receptor's intracellular domain changes shape, which may either activate its enzyme function or allow its binding to other molecules. The initial signal is amplified by most signal transduction pathways. This means that a single ligand molecule can activate multiple molecules of a downstream target. Proteins that relay a signal are most commonly phosphorylated at one or more sites, activating or inactivating the protein. Kinases catalyze...
18.9K
Wave Parameters01:10

Wave Parameters

The simplest mechanical waves are associated with simple harmonic motion and repeat themselves for several cycles. These simple harmonic waves can be modeled using a combination of sine and cosine functions. Consider a simplified surface water wave that moves across the water's surface. Unlike complex ocean waves, in surface water waves, water moves vertically, oscillating up and down, whereas the disturbance of the wave moves horizontally through the medium. If a seagull is floating on the...
9.5K
MOSFET Amplifiers01:17

MOSFET Amplifiers

The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
602
Design Example: Capacitance Multiplier Circuit01:20

Design Example: Capacitance Multiplier Circuit

In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
1.6K
Sum and Difference OpAmps01:22

Sum and Difference OpAmps

Operational amplifiers (op-amps) are versatile devices that extend beyond amplification. In this context, two specific op-amp configurations are explored: the summing and difference amplifiers.
A summing amplifier, or an adder, utilizes an op-amp to merge multiple input signals into a single output signal. When audio signals are introduced into its input channels, the input resistors initiate currents that traverse feedback resistors, resulting in an output voltage. Applying Kirchhoff's current...
1.5K