Related Experiment Video
Updated: Mar 2, 2026
08:15
Three-Dimensional Preoperative Virtual Planning in Derotational Proximal Femoral Osteotomy
Published on: February 17, 2023
1.5K
Erratum: Figure Correction.
Soo Ah Kim1,2, Mi Jung Um1, Han Kyoung Kim1,2
1Department of Obstetrics and Gynecology, Chosun University Hospital, Gwangju, Korea.
Obstetrics & Gynecology Science
|May 24, 2017
Summary
This study corrects a previous publication. The correction pertains to information presented on page 506 of volume 59, referencing PMID 27896253.
Area of Science:
- Scientific publishing
- Article errata
- Biomedical research communication
Context:
- A previous article requires correction.
- Details of the correction are specified.
Purpose:
- To ensure accuracy in the scientific record.
- To provide updated information to readers.
Summary:
- Correction issued for an article published in volume 59.
- The specific page number for the correction is 506.
- The article is identified by its PMID: 27896253.
Impact:
- Maintains the integrity of published scientific literature.
- Facilitates accurate referencing and data retrieval.
- Supports reliable scientific discourse and future research.
Related Concept Videos
01:12Adjusting a Traverse
403
In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
403
01:15Distance Corrections
332
To achieve precise distance measurements, especially in surveying and construction, certain corrections must be applied to account for potential sources of error like the standardization errors, temperature variations, and slope adjustments.Standardization error emerges when measurement equipment undergoes changes, such as wear, repairs, or weather impacts. To address this, surveyors compare the equipment’s readings to a standard. This process identifies any deviation that might lead to...
332
01:18Errors in Taping
392
Errors in taping arise from multiple factors that can significantly impact measurement accuracy in surveying. Misalignment of the tape, often due to human error, is one primary source. A skilled rear tapeman, using a telescope, can help correct alignment by guiding the head tapeman; however, human limitations still lead to small inaccuracies. These errors may include misplacement of pins or inaccurate tape readings due to common visual confusions, such as mistaking a six for a nine. Such...
392
01:20Midpoint Rule
85
Approximating areas under curved boundaries is a common problem in applied mathematics, particularly when an exact calculation is difficult or impractical. One effective numerical method for this purpose is the Midpoint Rule, which provides an estimate of the area under a curve by using rectangular approximations over a specified interval.Description of the Midpoint RuleThe Midpoint Rule begins by dividing the given interval into a number of equal subintervals. For each subinterval, the...
85
01:14NMR Spectrometers: Resolution and Error Correction
1.1K
When magnetic nuclei in a sample achieve resonance and undergo relaxation, the signal detected in NMR is an approximately exponential free induction decay. Fourier transform of an exponential decay yields a Lorentzian peak in the frequency domain. Lorentzian peaks in an NMR spectrum are defined by their amplitude, full width at half maximum, and position, where the peak width is governed by the spin-spin relaxation time alone. In real experiments, however, the applied magnetic field is rendered...
1.1K
01:21Deformations in a Transverse Cross Section
678
When a material is subjected to uniaxial stress, it elongates or contracts in the direction of the applied force, and also undergoes changes in the perpendicular directions. This behavior is crucial for understanding how materials behave under stress and is governed by mechanical properties such as Poisson's ratio v, which measures the ratio of transverse strain to axial strain.
As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
As the material stretches, it expands or contracts in orthogonal directions to the load. This phenomenon varies...
678