Related Experiment Video

Updated: Dec 21, 2025

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices
11:24

Optimized Fabrication Procedure for High-Quality Graphene-based Moiré Superlattice Devices

Published on: July 11, 2025

14.0K

Valley precession and valley polarization in graphene with inter-valley coupling

Qing-Ping Wu1,2, Zheng-Fang Liu1,2, Ai-Xi Chen1,3

  • 1Department of Applied Physics, East China Jiaotong University, Nanchang 330013, People's Republic of China.

Journal of Physics. Condensed Matter : an Institute of Physics Journal
|July 20, 2017
PubMed
Abstract

More Related Videos

Fabricating van der Waals Heterostructures with Precise Rotational Alignment09:25

Fabricating van der Waals Heterostructures with Precise Rotational Alignment

Published on: July 5, 2019

9.9K
Fabrication of Gate-tunable Graphene Devices for Scanning Tunneling Microscopy Studies with Coulomb Impurities11:42

Fabrication of Gate-tunable Graphene Devices for Scanning Tunneling Microscopy Studies with Coulomb Impurities

Published on: July 24, 2015

15.9K

Related Concept Videos

Spin–Spin Coupling: Three-Bond Coupling (Vicinal Coupling)01:22

Spin–Spin Coupling: Three-Bond Coupling (Vicinal Coupling)

Vicinal or three-bond coupling is commonly observed between protons attached to adjacent carbons. Here, nuclear spin information is primarily transferred via electron spin interactions between adjacent C‑H bond orbitals. This generally favors the antiparallel arrangement of spins, so 3J values are usually positive.
The extent of coupling depends on the C‑C bond length, the two H‑C‑C angles, any electron-withdrawing substituents, and the dihedral angle between the involved orbitals. The...
1.4K
Spin–Spin Coupling: Two-Bond Coupling (Geminal Coupling)01:20

Spin–Spin Coupling: Two-Bond Coupling (Geminal Coupling)

Two NMR-active nuclei bonded to a central atom can be involved in geminal or two-bond coupling. Geminal coupling is commonly seen between diastereotopic protons in chiral molecules and unsymmetrical alkenes, among others.
The central atom need not be NMR-active because its electrons are affected by the electron polarization of the spin-active atoms. However, spin information is transmitted less effectively than in one-bond coupling, and 2J values are usually weaker than 1J values. The energy of...
1.5K
Spin–Spin Coupling: One-Bond Coupling01:17

Spin–Spin Coupling: One-Bond Coupling

Coupling interactions are strongest between NMR-active nuclei bonded to each other, where spin information can be transmitted directly through the pair of bonding electrons. While nuclei polarize their electrons to the opposite spins, the bonding electron pair has opposite spins. Configurations with antiparallel nuclear spins are expected to be lower in energy. When coupling makes antiparallel states more favorable, J is considered to have a positive value. The one-bond coupling constant, 1J,...
1.3K
Induced Electric Dipoles01:28

Induced Electric Dipoles

A permanent electric dipole orients itself along an external electric field. This rotation can be quantified by defining the potential energy because the external torque does work in rotating it. Then, the potential energy is minimum at the parallel configuration and maximum at the antiparallel configuration. While the former is a stable equilibrium, the latter is an unstable equilibrium.
Since the absolute value of potential energy holds no physical meaning, its zero value can be chosen as per...
4.6K
Spin–Spin Coupling Constant: Overview01:08

Spin–Spin Coupling Constant: Overview

In bromoethane, the three methyl protons are coupled to the two methylene protons that are three bonds away. In accordance with the n+1 rule, the signal from the methyl protons is split into three peaks with 1:2:1 relative intensities. The methylene protons appear as a quartet, with the relative intensities of 1:3:3:1.
Qualitatively, any spin plus-half nucleus polarizes the spins of its electrons to the minus-half state. Consequently, the paired electron in the hydrogen–carbon bond must...
1.3K
Biasing of Metal-Semiconductor Junctions01:27

Biasing of Metal-Semiconductor Junctions

Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
476