Double Hall sensor structure reducing voltage offset

Related Experiment Video

Updated: Feb 25, 2026

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver
08:25

Construction of a Wireless-Enabled Endoscopically Implantable Sensor for pH Monitoring with Zero-Bias Schottky Diode-based Receiver

Published on: August 27, 2021

3.0K

M Oszwaldowski1, S El-Ahmar2

  • 1Poznan University of Technology, Piotrowo 3, 60-965 Poznan, Poland.

The Review of Scientific Instruments
|August 3, 2017
PubMed

More Related Videos

Optimization, Test and Diagnostics of Miniaturized Hall Thrusters12:22

Optimization, Test and Diagnostics of Miniaturized Hall Thrusters

Published on: February 16, 2019

9.6K
High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition05:11

High-precision Electromagnetic Flowmeter with Empty Pipe Detection via Complex Programmable Logic Device-based Waveform Recognition

Published on: June 27, 2025

738

Related Concept Videos

The Hall Effect01:30

The Hall Effect

Edwin H. Hall, in the year 1879, devised an experiment that could be used to identify the polarity of the predominant charge carriers in a conducting material. From a historical perspective, this experiment was the first to demonstrate that the charge carriers in most metals are negative.
4.6K
Voltage Doubler Circuit01:23

Voltage Doubler Circuit

A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
1.9K
Voltage Dividers01:14

Voltage Dividers

In electrical circuits, resistors can be connected in series, sequentially linked one after the other. In a series configuration, the same current flows through each resistor. Ohm's law is a fundamental principle to understand the behavior of resistors in series. It expresses the voltage across these resistors in terms of the current and resistance.
Kirchhoff's voltage law implies that the sum of the voltages across the resistors in series equals the source voltage. This means that the current...
1.4K
Biasing of Metal-Semiconductor Junctions01:27

Biasing of Metal-Semiconductor Junctions

Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
709
Biasing of FET01:22

Biasing of FET

Biasing a Junction Field Effect Transistor (JFET) is crucial for setting operational parameters and ensuring efficient functioning in electronic circuits. JFETs are characterized by using a single carrier type in N-channel or P-channel configurations, where the channel is surrounded by PN junctions. These junctions are central to the device's ability to control current flow.
In an N-channel JFET, the structure consists of N-type material forming the channel on a P-type substrate, with the...
777
Diode: Forward bias01:20

Diode: Forward bias

In semiconductor devices, diodes play a crucial role in directing current flow, and its operation is primarily categorized into forward bias and reverse bias. A diode is said to be forward-biased when its p-type region is connected to the positive terminal of a battery and its n-type region is linked to the negative terminal. This configuration reduces the potential barrier within the diode, allowing current to flow easily from the p to the n-type region.
The behavior of a diode in forward bias...
2.4K