Related Experiment Video

Updated: Feb 25, 2026

A Fabrication and Measurement Method for a Flexible Ferroelectric Element Based on Van Der Waals Heteroepitaxy
10:40

A Fabrication and Measurement Method for a Flexible Ferroelectric Element Based on Van Der Waals Heteroepitaxy

Published on: April 8, 2018

8.7K

Self-referenced antiresonant reflecting guidance mechanism for directional bending sensing with low temperature and

Ran Gao, Danfeng Lu, Jin Cheng

    Optics Express
    |August 10, 2017
    PubMed

    More Related Videos

    Fabrication and Characterization of Superconducting Resonators10:26

    Fabrication and Characterization of Superconducting Resonators

    Published on: May 21, 2016

    12.0K
    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators11:44

    Real-Time DC-dynamic Biasing Method for Switching Time Improvement in Severely Underdamped Fringing-field Electrostatic MEMS Actuators

    Published on: August 15, 2014

    10.8K

    Related Concept Videos

    Temperature Dependent Deformation01:12

    Temperature Dependent Deformation

    In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
    454
    Unsymmetric Bending - Angle of Neutral Axis01:15

    Unsymmetric Bending - Angle of Neutral Axis

    Unsymmetrical bending occurs when a structural member is subjected to bending moments in a plane that does not align with the member's principal axes. This scenario typically arises in beams and other structural components when loads are applied at non-ideal angles, introducing complexities in stress analysis.
    When a bending moment is applied at an angle θ concerning the vertical axis of a symmetrical member, it can be resolved into components along the member's principal...
    918
    Design Example: Strain Gauge Bridge or Wheatstone Bridge01:15

    Design Example: Strain Gauge Bridge or Wheatstone Bridge

    The utilization of strain gauges as transducers for converting mechanical strain into electrical signals is a common practice in various engineering applications. These strain gauges are frequently integrated into Wheatstone bridge circuits to accurately measure parameters such as force or pressure. Within this context, each element within the circuit exhibits a resistance that undergoes subtle variations when subjected to mechanical strain. The primary objective is to convert minuscule...
    1.1K
    Residual Stresses in Bending01:18

    Residual Stresses in Bending

    In the study of elastoplastic members subjected to bending moments, understanding the loading and unloading phases is crucial for assessing material behavior and structural integrity. During the loading phase, as the bending moment increases, the material initially responds elastically, adhering to Hooke's Law, where stress is directly proportional to strain. When the load exceeds the yield strength, plastic deformation occurs, resulting in permanent strain and deformation that remains even...
    604
    Biasing of Metal-Semiconductor Junctions01:27

    Biasing of Metal-Semiconductor Junctions

    Biasing metal-semiconductor junctions involves applying a voltage across the junction. Specifically, the metal is connected to a voltage source, while the semiconductor is grounded. This technique is essential for controlling the direction and magnitude of current flow in electronic devices, including diodes, transistors, and photovoltaic cells.
    In Schottky junctions, where the semiconductor is n-type, applying a positive voltage to the metal relative to the semiconductor reduces its Fermi...
    705
    Deformations in a Symmetric Member in Bending01:18

    Deformations in a Symmetric Member in Bending

    When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
    When the member is segmented into tiny cubic elements, it is observed that the primary stress...
    553