Related Experiment Video

Updated: Feb 22, 2026

Applying Hyperspectral Reflectance Imaging to Investigate the Palettes and the Techniques of Painters
07:05

Applying Hyperspectral Reflectance Imaging to Investigate the Palettes and the Techniques of Painters

Published on: June 18, 2021

2.9K

Edge-Preserving Image Smoothing Constraint in Multivariate Curve Resolution-Alternating Least Squares (MCR-ALS) of

Siewert Hugelier1, Raffaele Vitale1,2, Cyril Ruckebusch1

  • 11 27022 Université de Lille, Sciences et Technologies, LASIR, CNRS, Lille, France.

Applied Spectroscopy
|September 20, 2017
PubMed

Keywords:
Hyperspectral image analysisMCR-ALSconstraintedge preservationmultivariate curve resolution–alternating least squaresspatial smoothing

More Related Videos

Surface Mapping of Earth-like Exoplanets using Single Point Light Curves06:48

Surface Mapping of Earth-like Exoplanets using Single Point Light Curves

Published on: May 10, 2020

4.0K
A Multimodal Wide-Field Fourier-Transform Raman Microscope06:48

A Multimodal Wide-Field Fourier-Transform Raman Microscope

Published on: December 30, 2025

551

Related Concept Videos

Calibration Curves: Linear Least Squares01:20

Calibration Curves: Linear Least Squares

A calibration curve is a plot of the instrument's response against a series of known concentrations of a substance. This curve is used to set the instrument response levels, using the substance and its concentrations as standards. Alternatively, or additionally, an equation is fitted to the calibration curve plot and subsequently used to calculate the unknown concentrations of other samples reliably.
For data that follow a straight line, the standard method for fitting is the linear...
4.6K
Residuals and Least-Squares Property01:11

Residuals and Least-Squares Property

The vertical distance between the actual value of y and the estimated value of y. In other words, it measures the vertical distance between the actual data point and the predicted point on the line
If the observed data point lies above the line, the residual is positive, and the line underestimates the actual data value for y. If the observed data point lies below the line, the residual is negative, and the line overestimates the actual data value for y.
The process of fitting the best-fit...
9.6K
Elevation of Intermediate Points on Vertical Curves01:20

Elevation of Intermediate Points on Vertical Curves

Vertical curves are essential in roadway design because they provide smooth transitions between varying roadway grades. Designing vertical curves involves calculating intermediate elevations and identifying the curve's highest or lowest point, which is essential for optimal roadway performance.Intermediate elevations on a vertical curve are determined using the tangent offset method. This method considers the initial elevation at the start of the curve, the grades, and the curve's geometry. The...
324
Curvilinear Motion: Rectangular Components01:23

Curvilinear Motion: Rectangular Components

Curvilinear motion characterizes the movement of a particle or object along a curved path, notably evident when envisioning a car navigating a winding road. If the car starts at point A, its position vector is established within a fixed frame of reference, where the ratio of the position vector to its magnitude signifies the unit vector pointing in the position vector's direction.
As the car advances, its position evolves over time. Quantifying the car's velocity involves computing the...
1.4K
Boundary Conditions: Lossless Lines01:21

Boundary Conditions: Lossless Lines

Consider a single-phase, two-wire, lossless transmission line terminated by an impedance at the receiving end and a source with Thevenin voltage and impedance at the sending end. The line, with length, has a surge impedance and wave velocity determined by the line's inductance and capacitance.
At the receiving end, the boundary condition states that the voltage equals the product of the receiving-end impedance and current. This relationship is expressed as a function of the incident and...
443
Skewness01:06

Skewness

The measures of central tendency calculated from a data set may not reveal much about its intrinsic distribution. If a plot is made of the data set’s values, the mean and the median may not only differ, but also the plot may have more values on one side of the central tendencies. Such a data set is said to be skewed towards that side.
The longer the tail of the plot on one side, the more skewed it is. The skewness of a data set’s values suggests that the measures of central tendency...
19.8K