Related Experiment Video
Updated: Feb 19, 2026
09:57
Multiplex Chemical Imaging Based on Broadband Stimulated Raman Scattering Microscopy
Published on: July 25, 2022
4.6K
Matrix multi-pass scheme disk amplifier
Applied Optics
|November 2, 2017
Summary
Two novel multi-pass optical schemes for disk laser amplifiers were developed and calculated. These designs achieved approximately 50W average power with 10% efficiency, demonstrating significant advancements in laser amplification technology.
Area of Science:
- Laser Physics
- Optical Engineering
Background:
- Disk laser amplifiers are crucial for high-power laser systems.
- Optimizing optical schemes is key to enhancing amplifier performance.
Purpose of the Study:
- To propose and analyze novel multi-pass optical schemes for disk laser amplifiers.
- To minimize optical elements and account for active element lensing.
Main Methods:
- Theoretical calculation and simulation of two distinct multi-pass optical schemes.
- Optimization of schemes considering minimal optical elements and active element lens effects.
- Analysis of amplifier performance in a pulse-periodic regime.
Main Results:
- Achieved an average output power of approximately 50W.
- Reached an optical-to-optical efficiency of around 10%.
- Demonstrated a small signal gain of 200 with 64 passes.
Conclusions:
- The proposed multi-pass optical schemes are effective for high-power disk laser amplification.
- The designs offer a balance between efficiency, power, and gain.
- Further development could lead to even more efficient laser systems.
Related Concept Videos
01:16Cascaded Op Amps
1.2K
Operational amplifiers (op-amps) are versatile electronic components that can be interconnected in a cascade - one after another in a linear sequence. This cascading is possible due to their infinite input resistance and zero output resistance, allowing them to maintain their input-output relationships even when connected in series.
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
In a cascaded system, each op-amp is referred to as a stage. The output of one stage drives the input of the subsequent stage. As the input signal passes through...
1.2K
01:20Design Example: Capacitance Multiplier Circuit
1.6K
In integrated circuit technology, a capacitance multiplier is often utilized to produce a larger capacitance value when a small physical capacitance falls short. This is achieved by a circuit that multiplies capacitance values by a factor of up to 1000, such that a 10-pF capacitor can replicate the performance of a 100-nF capacitor.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
The circuit illustrated in Figure 1 below incorporates two op-amps, with the first operating as a voltage follower and the second acting as an inverting amplifier.
1.6K
01:17MOSFET Amplifiers
573
The MOSFET, when operating in its active region, functions as a voltage-controlled current source. In this region, the gate-to-source voltage controls the drain current. This principle underlies the operation of the transconductance MOSFET amplifier. The output current is directed through a load resistor to convert this amplifier into a voltage amplifier. The output voltage is then obtained by subtracting the voltage drop across the load resistance from the supply voltage. This process results...
573
01:23Voltage Doubler Circuit
1.9K
A voltage doubler circuit integrates two main components: a clamping section and a rectifier section. The clamping section consists of a capacitor (C1) and a diode (D1), whereas the rectifier section is equipped with another diode (D2) and capacitor (C2). This circuit produces an output voltage with twice the amplitude of the sinusoidal input voltage.
1.9K
01:17Bandpass Sampling
557
In signal processing, bandpass sampling is an effective technique for sampling signals that have most of their energy concentrated within a narrow frequency band. This type of signal is known as a bandpass signal. The key principle of bandpass sampling involves sampling the signal at a rate that is greater than twice the signal's bandwidth to prevent aliasing.
A bandpass signal has a spectrum with a lower frequency limit, denoted as ω1, and an upper frequency limit, denoted as ω2....
A bandpass signal has a spectrum with a lower frequency limit, denoted as ω1, and an upper frequency limit, denoted as ω2....
557
01:23Small-Signal Analysis of MOSFET Amplifiers
1.2K
In small-signal analysis, a MOSFET transistor amplifier acts as a linear amplifier when operating in its saturation region. The gate-to-source voltage (VGS) of the MOSFET is the sum of the DC biasing voltage and the small time-varying input signal. This combination sets up the operating point and modulates the drain current (ID) that flows from the drain to the source. When a small AC signal is superimposed on the DC bias voltage at the gate, the instantaneous drain current comprises three...
1.2K