Related Experiment Video

Updated: Feb 19, 2026

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires
08:46

Force System with Vertical V-Bends: A 3D In Vitro Assessment of Elastic and Rigid Rectangular Archwires

Published on: July 24, 2018

11.3K

A comparison of orthodontic elastic forces: Focus on reduced inventory

Ameerah Y Mansour1

  • 1Department of Dental Public Health, Faculty of Dentistry, King Abdulaziz University, Jeddah, Kingdom of Saudi Arabia.

Journal of Orthodontic Science
|November 10, 2017
PubMed
Abstract

Keywords:
Force extensionorthodontic elasticsreduced inventory

More Related Videos

Author Spotlight: Insights into an Efficient Murine Maxillary Orthodontic Model Protocol04:11

Author Spotlight: Insights into an Efficient Murine Maxillary Orthodontic Model Protocol

Published on: October 27, 2023

1.4K
A Finite Element Approach for Locating the Center of Resistance of Maxillary Teeth10:50

A Finite Element Approach for Locating the Center of Resistance of Maxillary Teeth

Published on: April 8, 2020

10.2K

Related Concept Videos

Bending of Members Made of Several Materials01:11

Bending of Members Made of Several Materials

In analyzing a structural member composed of two different materials with identical cross-sectional areas, it is crucial to understand how their distinct elastic properties affect the member's response under load. The analysis involves assessing stress and strain distributions using the transformed section concept, which accounts for variations in material properties.
Hooke's Law determines stress in each material, stating that stress is proportional to strain but varies due to each material's...
635
Hooke's Law01:26

Hooke's Law

Hooke's law, a pivotal principle in material science, establishes that the strain a material undergoes is directly proportional to the applied stress, defined by a factor called the modulus of elasticity or Young's modulus.
1.6K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
426
Elastic Strain Energy for Normal Stresses01:22

Elastic Strain Energy for Normal Stresses

Strain energy quantifies the energy stored within a material due to deformation under loading conditions, a fundamental concept in materials science and engineering. The strain energy can be modeled when a material is subjected to axial loading with uniformly distributed stress. In this scenario, the stress experienced by the material is the internal force divided by the cross-sectional area, and the strain induced is directly proportional to this stress through the modulus of elasticity.
If...
630
Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity01:15

Relation between Poisson's ratio, Modulus of Elasticity and Modulus of Rigidity

Deformation occurs in axial and transverse directions when an axial load is applied to a slender bar. This deformation impacts the cubic element within the bar, transforming it into either a rectangular parallelepiped or a rhombus, contingent on its orientation. This transformation process induces shearing strain. Axial loading elicits both shearing and normal strains. Applying an axial load instigates equal normal and shearing stresses on elements oriented at a 45° angle to the load axis.
632
Stress Concentrations in Circular Shafts01:18

Stress Concentrations in Circular Shafts

Consider the elastic torsion formula, which applies to a circular shaft with a consistent cross-section. This formula assumes that the shaft's ends are loaded with rigid plates firmly attached. However, in many cases, torques are applied to the shaft through mechanisms like flange couplings or gears, which are connected by keys inserted into keyways. This application method modifies the stress distribution near the point of torque application, causing it to deviate from the distributions...
591