Related Experiment Video

Updated: Feb 16, 2026

Author Spotlight: Fabrication of a Low-Cost, Fiber-Coupled, and Air-Spaced Fabry-Pérot Etalon
07:22

Author Spotlight: Fabrication of a Low-Cost, Fiber-Coupled, and Air-Spaced Fabry-Pérot Etalon

Published on: February 3, 2023

8.5K

Traveling wave-like Fabry-Perot resonator-based add-drop filters

Qingzhong Huang, Qiang Liu, Jinsong Xia

    Optics Letters
    |December 15, 2017
    PubMed

    More Related Videos

    Fabrication and Testing of Microfluidic Optomechanical Oscillators09:10

    Fabrication and Testing of Microfluidic Optomechanical Oscillators

    Published on: May 29, 2014

    12.7K
    Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters15:25

    Design and Characterization Methodology for Efficient Wide Range Tunable MEMS Filters

    Published on: February 4, 2018

    6.6K

    Related Concept Videos

    Parallel Resonance01:23

    Parallel Resonance

    The parallel RLC circuit is an arrangement where the resistor (R), inductor (L), and capacitor (C) are all connected to the same nodes and, as a result, share the same voltage across them. The parallel RLC circuit is analyzed in terms of admittance (Y), which reflects the ease with which current can flow. The admittance is given by:
    618
    Active Filters01:25

    Active Filters

    Active filters are electronic circuits that use operational amplifiers (op-amps), resistors, and capacitors to filter out unwanted frequency components from a signal. A first-order low-pass active filter is designed to pass signals with a frequency lower than a certain cutoff frequency and attenuate frequencies higher than that cutoff frequency. The transfer function for a first-order low-pass active filter is:
    1.4K
    Passive Filters01:27

    Passive Filters

    Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
    Low-Pass Filters
    Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
    1.1K
    Characteristics of Series Resonant Circuit01:24

    Characteristics of Series Resonant Circuit

    Series resonance occurs in a circuit containing inductive (L), capacitive (C), and resistive (R) elements connected sequentially. At the resonance frequency, the inductive and capacitive reactances are equal in magnitude but opposite in sign, effectively canceling each other. This causes the circuit's impedance is minimal, primarily determined by the resistance R. The resonant frequency of an RLC circuit is defined as:
    692
    Second-order Op Amp Circuits01:19

    Second-order Op Amp Circuits

    Implementing second-order low-pass filters in audio systems is crucial in refining audio signals by eliminating undesirable high-frequency noise. These filters typically involve second-order op-amp circuits configured as voltage followers, encompassing two nodes with distinct storage elements.
    The analysis of such circuits follows a systematic approach, similar to the second-order RLC circuits. In practical scenarios, bulky inductors are rarely employed due to their size and weight. This means...
    656
    Op Amp AC Circuits01:18

    Op Amp AC Circuits

    Within an audio system, the filter circuit plays a pivotal role in processing the amplified audio signal from an amplifier. Its primary function is significantly attenuating signal components with lower frequencies, thereby shaping the audio output. This circuit's operations are examined, focusing on the fundamental filter configuration. This configuration involves an operational amplifier arranged in an inverting setup coupled with resistors (R1 and R2) and a capacitor (C1).
    531