Related Experiment Video

Updated: Feb 16, 2026

Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads
07:58

Automatic Laser-based Geometry Capture for Finite Element Analysis of Weld Beads

Published on: July 25, 2025

894

Accuracy and Repeatability of Trajectory Rod Measurement Using Laser Scanners

Eugene Liscio1,2, Helen Guryn1, Daniella Stoewner1

  • 1ai2-3D, 271 Jevlan Drive, Woodbridge, ON, L4L 8A4, Canada.

Journal of Forensic Sciences
|December 23, 2017
PubMed

Keywords:
3D forensicsballisticsbullet trajectoriesforensic sciencelaser scannershooting reconstruction

More Related Videos

The Frequency Domain Thermoreflectance Technique for Thermal Property Measurements09:10

The Frequency Domain Thermoreflectance Technique for Thermal Property Measurements

Published on: December 5, 2025

851
Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography06:09

Measuring 3D In-vivo Shoulder Kinematics using Biplanar Videoradiography

Published on: March 12, 2021

3.8K

Related Concept Videos

Common Leveling Mistakes and Errors01:17

Common Leveling Mistakes and Errors

A survey team is tasked with determining the elevation difference between points Point A and Point B, separated by uneven terrain. They use a leveling instrument and a leveling rod.Common MistakesMisreading the Rod: During a backsight reading at Point A, the instrumentman observes the rod partially obscured by tall grass. Instead of reading 1.135 m, they mistakenly record 1.735 m due to the misalignment of the crosshair with the wrong graduation. This error adds 0.600 m to all subsequent...
506
Adjusting a Traverse01:12

Adjusting a Traverse

In the site survey of a four-sided traverse, internal angles are essential to ensure geometric accuracy. The survey revealed that the sum of the measured internal angles was 359 degrees and 48 minutes, which is 12 minutes less than the expected 360 degrees. This discrepancy signals an error likely arising from measurement inaccuracies during the fieldwork.To rectify this error, the adjustment process involved distributing the 12-minute shortfall equally across the four internal angles. By...
390
Leveling Equipment01:18

Leveling Equipment

As leveling involves measuring vertical distances relative to a horizontal line of sight, it requires a graduated rod, called a level rod, for vertical measurements and an instrument called a level for a horizontal sight line. A level includes a high-powered telescope with a mechanism for leveling to ensure the line of sight is horizontal when the bubble in the spirit level is centered. Leveling rods, made of wood, metal, or fiberglass, are graduated in feet or meters and commonly used in two-...
456
Accuracy and Precision01:52

Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value.  Highly accurate...
15.9K
Distance Corrections01:15

Distance Corrections

To achieve precise distance measurements, especially in surveying and construction, certain corrections must be applied to account for potential sources of error like the standardization errors, temperature variations, and slope adjustments.Standardization error emerges when measurement equipment undergoes changes, such as wear, repairs, or weather impacts. To address this, surveyors compare the equipment’s readings to a standard. This process identifies any deviation that might lead to...
306
Uncertainty in Measurement: Accuracy and Precision03:37

Uncertainty in Measurement: Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value. 
106.6K