Related Experiment Video

Updated: Feb 13, 2026

Microarray-based Identification of Individual HERV Loci Expression: Application to Biomarker Discovery in Prostate Cancer
13:19

Microarray-based Identification of Individual HERV Loci Expression: Application to Biomarker Discovery in Prostate Cancer

Published on: November 2, 2013

17.2K

Accuracy and reproducibility of fetal-fraction measurement using relative quantitation at polymorphic loci with

M Schmid1, K White1, R Stokowski1

  • 1Ariosa Diagnostics Inc., Roche Sequencing Solutions Inc., San Jose, CA, USA.

Ultrasound in Obstetrics & Gynecology : the Official Journal of the International Society of Ultrasound in Obstetrics and Gynecology
|February 28, 2018
PubMed
Abstract

Keywords:
NIPTcell-free DNAfetal fractionprenatal screeningquality

More Related Videos

A Guided Materials Screening Approach for Developing Quantitative Sol-gel Derived Protein Microarrays10:44

A Guided Materials Screening Approach for Developing Quantitative Sol-gel Derived Protein Microarrays

Published on: August 26, 2013

14.6K
Use of an Influenza Antigen Microarray to Measure the Breadth of Serum Antibodies Across Virus Subtypes08:52

Use of an Influenza Antigen Microarray to Measure the Breadth of Serum Antibodies Across Virus Subtypes

Published on: July 26, 2019

8.7K

Related Concept Videos

Uncertainty in Measurement: Accuracy and Precision03:37

Uncertainty in Measurement: Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value. 
105.2K
Improving Translational Accuracy02:07

Improving Translational Accuracy

Base complementarity between the three base pairs of mRNA codon and the tRNA anticodon is not a failsafe mechanism. Inaccuracies can range from a single mismatch to no correct base pairing at all. The free energy difference between the correct and nearly correct base pairs can be as small as 3 kcal/ mol. With complementarity being the only proofreading step, the estimated error frequency would be one wrong amino acid in every 100 amino acids incorporated. However, error frequencies observed in...
15.0K
Improving Translational Accuracy02:07

Improving Translational Accuracy

3.7K
Accuracy and Precision01:52

Accuracy and Precision

Scientists typically make repeated measurements of a quantity to ensure the quality of their findings and to evaluate both the precision and the accuracy of their results. Measurements are said to be precise if they yield very similar results when repeated in the same manner. A measurement is considered accurate if it yields a result that is very close to the true or the accepted value. Precise values agree with each other; accurate values agree with a true value.  Highly accurate...
15.7K
Root Loci for Positive-Feedback Systems01:23

Root Loci for Positive-Feedback Systems

The Hartley oscillator is a positive feedback system that sustains oscillations by feeding the output back to the input in phase, thereby reinforcing the signal. Positive feedback systems can be viewed as negative feedback systems with inverted feedback signals. In these systems, the root locus encompasses all points on the s-plane where the angle of the system transfer function equals 360 degrees.
The construction rules for the root locus in positive feedback systems are similar to those in...
353
Accuracy, limits, and approximation01:28

Accuracy, limits, and approximation

Accuracy, limits, and approximations are common in many fields, especially in engineering calculations. These concepts are imperative for ensuring that a given value is as close as possible to its true value.
Accuracy is defined as the closeness of the measured value to the true or actual value. In engineering mechanics, repeated measurements are taken during theoretical or experimental analyses to ensure that the result is precise and accurate.
The accuracy of any solution is based on the...
1.3K