Related Experiment Video

Updated: Feb 13, 2026

An Experimental Human DIEP Flap Model to Investigate Preservation Strategies for Vascularized Composite Allografts and Free Flaps
07:57

An Experimental Human DIEP Flap Model to Investigate Preservation Strategies for Vascularized Composite Allografts and Free Flaps

Published on: December 5, 2025

289

Utilization of Microdissected Thin Perforator Flap Technique in the Treatment of Bulky and Deformed Skin Flaps

Zheng-Bing Zhou, Ding Pan, Pan-Feng Wu

  • 1Department of Plastic and Reconstructive Surgery, Johns Hopkins University, Baltimore, MD.

Annals of Plastic Surgery
|March 1, 2018
PubMed
Abstract

More Related Videos

Engineered Vascularized Muscle Flap08:18

Engineered Vascularized Muscle Flap

Published on: January 11, 2016

8.7K
Flapping Soft Fin Deformation Modeling using Planar Laser-Induced Fluorescence Imaging06:20

Flapping Soft Fin Deformation Modeling using Planar Laser-Induced Fluorescence Imaging

Published on: April 28, 2022

2.5K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
477
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
477
Esophageal Perforation-I: Introduction01:22

Esophageal Perforation-I: Introduction

Esophageal perforation is a severe medical condition characterized by a breach in the integrity of the esophageal wall. This breach can occur due to various factors such as trauma, medical procedures, or underlying diseases. When the esophageal wall is compromised, it allows food, fluids, and digestive juices into the chest cavity or adjacent structures, leading to potential complications and health risks.
The location of esophageal perforation can vary, occurring anywhere along the esophagus....
622
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
415
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
528
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
491