Related Experiment Video

Updated: Feb 13, 2026

A Two-Step Pyrolysis-Gas Chromatography Method with Mass Spectrometric Detection for Identification of Tattoo Ink Ingredients and Counterfeit Products
08:07

A Two-Step Pyrolysis-Gas Chromatography Method with Mass Spectrometric Detection for Identification of Tattoo Ink Ingredients and Counterfeit Products

Published on: May 22, 2019

11.6K

Thermokinetic analysis and product characterization of Medium Density Fiberboard pyrolysis

Dilan Irmak Aslan1, Buğçe Özoğul1, Selim Ceylan1

  • 1Ondokuz Mayıs University, Faculty of Engineering, Chemical Engineering Department, 55139 Kurupelit, Samsun, Turkey.

Bioresource Technology
|March 11, 2018
PubMed

Keywords:
KineticsMDFPyrolysisTG/DSC-FTIRpy/GC-MS

More Related Videos

Twin-Screw Extrusion Process to Produce Renewable Fiberboards07:21

Twin-Screw Extrusion Process to Produce Renewable Fiberboards

Published on: January 27, 2021

7.1K
Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor07:30

Fast Pyrolysis of Biomass Residues in a Twin-screw Mixing Reactor

Published on: September 9, 2016

28.3K

Related Concept Videos

Density00:56

Density

Density is an important characteristic of substances, crucial in determining whether an object sinks or floats in a fluid. Its SI unit is kg/m3, and its cgs unit is g/cm3. The density of an object helps in identifying its composition, and also reveals information about the phase of the matter and its substructure. The densities of liquids and solids are roughly comparable, consistent with the fact that their atoms are in close contact. However, gases have much lower densities than liquids and...
20.0K
Current Density01:21

Current Density

The total amount of current flowing through one unit value of a cross-sectional area is referred to as current density. If the current flow is uniform, the amount of current flowing through a conductor is the same at all points along the conductor, even if the conductor area varies. The current density consists of the local magnitude and direction of the charge flow, which varies from point to point. Current density is measured in amperes per meter square, and direction is defined as the net...
5.2K
Strain-Energy Density01:20

Strain-Energy Density

Understanding the strain energy density in materials under axial load is crucial for evaluating their mechanical behavior and durability. When a rod is subjected to such a load, it elongates and stores energy, known as strain energy, as potential energy within the material. This energy is measured in terms of energy per unit volume.
In the elastic region of a material, the relationship between the stress and the strain is linear and follows Hooke's Law. The strain energy density in this region...
943
Bulk Density of Aggregate01:22

Bulk Density of Aggregate

Bulk density refers to the mass of aggregate particles that would fill a unit volume. The concept of bulk density originates from the inability to pack aggregate particles in a manner that completely eliminates void spaces. Hence, the term bulk refers to the volume that encompasses both the aggregates and the voids. This measurement is crucial when aggregates are batched by volume and is used to convert quantities by mass to volume.
Most natural mineral aggregates, like sand and gravel,...
1.2K
Dimensional Analysis03:40

Dimensional Analysis

Dimensional analysis, also known as the factor label method, is a versatile approach for mathematical operations. The main principle behind this approach is: the units of quantities must be subjected to the same mathematical operations as their associated numbers. This method can be applied to computations ranging from simple unit conversions to more complex and multi-step calculations involving several different quantities and their units.
Conversion Factors and Dimensional Analysis
The unit...
65.3K
Density and Archimedes' Principle01:05

Density and Archimedes' Principle

When a lump of clay is dropped into water, it sinks. But if the same lump of clay is molded into the shape of a boat, it starts to float. Because of its shape, the clay boat displaces more water than the lump and experiences a greater buoyant force, even though its mass is the same. The same holds true for steel ships. The average density of an object majorly determines if the object will float. If an object's average density is less than that of the surrounding fluid, it will float. The...
8.9K