Related Experiment Video

Updated: Feb 12, 2026

Expression of Cementitious Pore Solution and the Analysis of Its Chemical Composition and Resistivity Using X-ray Fluorescence
06:27

Expression of Cementitious Pore Solution and the Analysis of Its Chemical Composition and Resistivity Using X-ray Fluorescence

Published on: September 23, 2018

9.8K

New Ablation-Resistant Material Candidate for Hypersonic Applications: Synthesis, Composition, and Oxidation

Victor V Lozanov1, Natalya I Baklanova1, Natalia V Bulina1

  • 1Institute of Solid State Chemistry and Mechanochemistry SB RAS , Kutateladze Street 18 , Novosibirsk 630128 , Russian Federation.

ACS Applied Materials & Interfaces
|March 29, 2018
PubMed

Keywords:
ablation resistancehafnium carbideintermetallicsiridiumsolid-state reaction

More Related Videos

Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of ChalcogenidoplumbatesII or IV10:42

Combining Solid-state and Solution-based Techniques: Synthesis and Reactivity of ChalcogenidoplumbatesII or IV

Published on: December 29, 2016

11.2K
Bulk and Thin Film Synthesis of Compositionally Variant Entropy-stabilized Oxides09:41

Bulk and Thin Film Synthesis of Compositionally Variant Entropy-stabilized Oxides

Published on: May 29, 2018

10.0K

Related Concept Videos

Resistivity01:22

Resistivity

When a voltage is applied to a conductor, an electrical field is generated, and charges in the conductor feel the force due to the electrical field. The current density that results depends on the electrical field and the properties of the material. In some materials, including metals at a given temperature, the current density is approximately proportional to the electrical field. In these cases, the current density can be modeled as:
4.6K
Resistance01:19

Resistance

When a current moves through any conductor, the conductor causes some level of difficulty for the current to flow. The measure of that difficulty is known as the resistance of the material and is represented by R. Every material has its own resistance. In the case of conductors, heat is emitted whenever a current passes through them. Resistance depends on the resistivity of the material. Resistivity is a characteristic of the material used to fabricate electrical components, whereas the...
6.1K
Solution Composition During Acid/Base Titrations01:17

Solution Composition During Acid/Base Titrations

The titration of a weak acid with a strong base results in the formation of water and the conjugate base of the acid. For instance, titrating acetic acid with sodium hydroxide leads to the formation of water and sodium acetate. A solution of acetic acid and sodium acetate constitutes a buffer whose relative concentration at different stages of the titration is indicated by the α values, which represent percentages of the weak acid and its conjugate base.
The α0 and α1 values...
1.6K
Equivalent Resistance01:16

Equivalent Resistance

In circuit analysis, situations often arise where resistors are neither in series nor parallel configurations. To tackle such scenarios, three-terminal equivalent networks like the wye (Y) (Figure 1 (a)) or tee (T) and delta (Δ) (Figure 1 (b)) or pi (π) networks come into play. These networks offer versatile solutions and are frequently encountered in various applications, including three-phase electrical systems, electrical filters, and matching networks.
1000
Resistance and Conductance01:25

Resistance and Conductance

A conductor's DC resistance at a given temperature is influenced by its resistivity, length, and cross-sectional area. Resistivity is an inherent property of the conductor material, with annealed copper serving as the international standard for measurement. For instance, the resistivity of hard-drawn aluminum at 20 degrees Celsius is 61% of the standard conductivity of annealed copper.
Various factors impact the resistance of a conductor. Spiraling in stranded conductors increases their...
531
Rolling Resistance01:21

Rolling Resistance

When a solid cylinder rolls steadily on a rigid surface, the normal force applied by the surface on the cylinder is perpendicular to the tangent at the contact point. However, since no materials are entirely rigid, the surface's reaction to the cylinder involves a range of normal pressures.
For instance, imagine a hard cylinder rolling on a comparatively soft surface. The cylinder's weight compresses the surface beneath it. As the cylinder moves, the material in front of it slows down due to...
679