Related Experiment Video

Updated: Feb 12, 2026

Experimental Investigation of the Flow Structure over a Delta Wing Via Flow Visualization Methods
09:17

Experimental Investigation of the Flow Structure over a Delta Wing Via Flow Visualization Methods

Published on: April 23, 2018

11.3K

Deformation behavior of dragonfly-inspired nodus structured wing in gliding flight through experimental visualization

Sheng Zhang1, Yuta Sunami2,3, Hiromu Hashimoto4

  • 1Micro/Nano Technology Center, Tokai University, 4-1-1 Kitakaname, Hiratsuka-city, Kanagawa, 259-1292, Japan. szhang84@hotmail.com.

Scientific Reports
|April 12, 2018
PubMed

More Related Videos

Dissection of Drosophila melanogaster Indirect Flight Muscles for Microscopy Approaches09:47

Dissection of Drosophila melanogaster Indirect Flight Muscles for Microscopy Approaches

Published on: November 7, 2025

937
A Simple Flight Mill for the Study of Tethered Flight in Insects07:42

A Simple Flight Mill for the Study of Tethered Flight in Insects

Published on: December 10, 2015

17.8K

Related Concept Videos

Mechanism of Breathing I: Inspiration01:30

Mechanism of Breathing I: Inspiration

Introduction to Inspiration: The Respiratory System in Action
The respiratory system, an essential network for breathing, comprises the conducting and respiratory zones, each playing a crucial role in the overall process of respiration. Let us explore the detailed mechanism of inspiration, or inhalation, which is the first phase of the respiratory cycle.
Pathway of Air during Inspiration
During inspiration, air enters our body through the nose or mouth and moves through the conducting zone,...
3.3K
Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
477
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
477
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
415
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
528
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
491