Related Experiment Video

Updated: Feb 11, 2026

Laboratory Production of Biofuels and Biochemicals from a Rapeseed Oil through Catalytic Cracking Conversion
11:33

Laboratory Production of Biofuels and Biochemicals from a Rapeseed Oil through Catalytic Cracking Conversion

Published on: September 2, 2016

14.4K

Optimizing photon dose and frequency to enhance lipid productivity of thermophilic algae for biofuel production

Said Abu-Ghosh1, Zvy Dubinsky2, Gabi Banet3

  • 1The Mina and Everard Goodman Faculty of Life Sciences, Bar-Ilan University, Ramat-Gan 5290002, Israel; Bar Ilan Institute of Nanotechnology and Advanced Materials (BINA), Bar-Ilan University, Ramat-Gan 5290002, Israel.

Bioresource Technology
|April 18, 2018
PubMed

Keywords:
BiofuelBiomassFlashing lightMicractiniumTAGThermophilic algae

More Related Videos

Genetic Engineering of an Unconventional Yeast for Renewable Biofuel and Biochemical Production10:10

Genetic Engineering of an Unconventional Yeast for Renewable Biofuel and Biochemical Production

Published on: September 20, 2016

15.2K
Production of siRNA-Loaded Lipid Nanoparticles using a Microfluidic Device06:02

Production of siRNA-Loaded Lipid Nanoparticles using a Microfluidic Device

Published on: March 22, 2022

10.6K

Related Concept Videos

Dose Size and Dosing Frequency: Determination Methods01:21

Dose Size and Dosing Frequency: Determination Methods

Determining the optimal dose size and dosing frequency in pharmacotherapy is crucial for achieving therapeutic effectiveness while minimizing adverse effects. This article explores the methodologies employed in determining these parameters, focusing on their significance and interplay to tailor dosing regimens.Dose Size: Dose size refers to the amount of a drug administered in a single dose. It is determined based on the drug's pharmacodynamics and pharmacokinetics properties and...
320
Scalar Product (Dot Product)01:11

Scalar Product (Dot Product)

The scalar multiplication of two vectors is known as the scalar or dot product. As the name indicates, the scalar product of two vectors results in a number, that is, a scalar quantity. Scalar products are used to define work and energy relations. For example, the work that a force (a vector) performs on an object while causing its displacement (a vector) is defined as a scalar product of the force vector with the displacement vector.
The scalar product of two vectors is obtained by multiplying...
27.8K
Vector Product (Cross Product)01:17

Vector Product (Cross Product)

Vector multiplication of two vectors yields a vector product, with the magnitude equal to the product of the individual vectors multiplied by the sine of the angle between both the vectors and the direction perpendicular to both the individual vectors. As there are always two directions perpendicular to a given plane, one on each side, the direction of the vector product is governed by the right-hand thumb rule.
Consider the cross product of two vectors. Imagine rotating the first vector about...
28.1K
Primary Production01:06

Primary Production

The total amount of energy acquired by primary producers in an ecosystem is called gross primary production (GPP). However, of this energy, producers use some for metabolic processes, and some is lost as heat, decreasing the amount of energy available to the next trophic level. The remaining usable amount of energy is called the net primary productivity (NPP). In terrestrial ecosystems, NPP is driven by climate, while light penetration and nutrient availability drive NPP in aquatic ecosystems.
25.5K
Production Efficiency01:01

Production Efficiency

Net production efficiency (NPE) is the efficiency at which organisms assimilate energy into biomass for the next trophic level. Due to low metabolic rates and less energy spent on thermoregulatory processes, the NPE of ectotherms (cold-blooded animals) is 10 times higher than endotherms (warm-blooded animals).
18.5K
The Dot Product01:26

The Dot Product

Measuring how one directional quantity affects another along a specific path involves comparing their orientation and strength. When two such quantities are represented using direction and amount, a numerical result is computed to show how much one acts along the path of the other. This result comes from a rule combining both inputs' horizontal and vertical parts and adding the results.This calculation gives a single value that grows larger when both inputs point in similar directions and...
266