Related Experiment Video

Updated: Feb 11, 2026

Quantitative Atomic-Site Analysis of Functional Dopants/Point Defects in Crystalline Materials by Electron-Channeling-Enhanced Microanalysis
07:24

Quantitative Atomic-Site Analysis of Functional Dopants/Point Defects in Crystalline Materials by Electron-Channeling-Enhanced Microanalysis

Published on: May 10, 2021

6.9K

Effect of annealing temperature and dopant concentration on the thermoluminescence sensitivity in LiF:Mg,Cu,Ag

Akram Yahyaabadi1, Falamarz Torkzadeh2, Dariush Rezaei Ochbelagh3,4

  • 1Department of Physics, University of Mohaghegh Ardabili, Ardabil, Iran.

Luminescence : the Journal of Biological and Chemical Luminescence
|April 25, 2018
PubMed

Keywords:
Cu,AgLiF:Mgannealingsensitivitythermoluminescence

More Related Videos

Microfluidic Production of Lysolipid-Containing Temperature-Sensitive Liposomes09:51

Microfluidic Production of Lysolipid-Containing Temperature-Sensitive Liposomes

Published on: March 3, 2020

9.8K
Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy07:44

Characterization of Full Set Material Constants and Their Temperature Dependence for Piezoelectric Materials Using Resonant Ultrasound Spectroscopy

Published on: April 27, 2016

10.1K

Related Concept Videos

Concentration Cells02:41

Concentration Cells

A concentration cell is a type of a  voltaic cell constructed by connecting two almost identical half-cells, both based on the same half-reaction and using the same electrode, differing only in the concentration of one redox species. A concentration cell's potential, therefore, is determined only by the concentration difference of the particular redox species.
Consider the following voltaic cell:
25.9K
Temperature Dependence on Reaction Rate02:55

Temperature Dependence on Reaction Rate

The Collision Theory
Atoms, molecules, or ions must collide before they can react with each other. Atoms must be close together to form chemical bonds. This premise is the basis for a theory that explains many observations regarding chemical kinetics, including factors affecting reaction rates.
The collision theory is based on the postulates that (i) the reaction rate is proportional to the rate of reactant collisions, (ii) the reacting species collide in an orientation allowing contact between...
89.3K
Solution Concentration and Dilution02:59

Solution Concentration and Dilution

The relative amount of a given solution component is known as its concentration. Often, though not always, a solution contains one component with a concentration that is significantly greater than that of all other components. This component is called the solvent and may be viewed as the medium in which the other components are dispersed or dissolved. Solutions in which water is the solvent are, of course, very common on our planet. A solution in which water is the solvent is called an aqueous...
135.2K
Stress Concentrations01:13

Stress Concentrations

The concept of stress concentration is crucial for understanding how materials respond under bending stresses, particularly when there are irregularities or discontinuities in the material's geometry. Normally, stress in a symmetric member subjected to pure bending is assumed to be uniformly distributed across the entire cross-section. However, this assumption does not hold when there are variations in the cross-sectional geometry or the presence of notches and holes.
The stress...
657
Genetic Material01:20

Genetic Material

Within the human body, a complex and detailed system of trillions of cells works in unison to sustain life. Each cell houses a nucleus, which contains 46 chromosomes divided into 23 pairs. Chromosomes are highly coiled structures made of the genetic material DNA. These chromosomes are essential carriers of genetic information, with half inherited from the mother through her egg and the other half from the father's sperm, combining to create the unique genetic makeup of an individual.
3.8K
Members Made of Elastoplastic Material01:19

Members Made of Elastoplastic Material

The behavior of elastoplastic materials under bending stresses, particularly in structural members with rectangular cross-sections, is crucial for predicting material responses and understanding failure modes. Initially, when a bending moment is applied, the stress distribution across the section follows Hooke's Law and is linear and elastic. This distribution means the stress increases from the neutral axis to the maximum at the outer fibers, up to the elastic limit.
As the bending moment...
414