Related Experiment Video

Updated: Feb 11, 2026

An Anatomical Study of Nerves at Risk During Minimally Invasive Hallux Valgus Surgery
15:04

An Anatomical Study of Nerves at Risk During Minimally Invasive Hallux Valgus Surgery

Published on: February 17, 2018

12.8K

Hallux Valgus Deformity and Treatment: A Three-Dimensional Approach

Jesse Forbes Doty1, Wallace Taylor Harris2

  • 1UT Erlanger Orthopaedics, University of Tennessee College of Medicine, 979 East Third Street C225, Chattanooga, TN 37405, USA.

Foot and Ankle Clinics
|May 7, 2018
PubMed

Keywords:
First metatarsocuneiform jointFirst rayHallux valgusHallux valgus angleHypermobilityIntermetatarsal angle

More Related Videos

Treatment of Facial Deformities using 3D Planning and Printing of Patient-Specific Implants07:11

Treatment of Facial Deformities using 3D Planning and Printing of Patient-Specific Implants

Published on: May 23, 2020

8.0K
Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach09:01

Treatment of Ankle Osteoarthritis with Total Ankle Replacement Through a Lateral Transfibular Approach

Published on: January 24, 2018

12.4K

Related Concept Videos

Plastic Deformations01:19

Plastic Deformations

Plastic deformation represents a fundamental concept in materials science, which explains the irreversible change in the shape of a material when it experiences stress beyond its elastic capability. This phenomenon is important in structural engineering, especially in designing and analyzing cantilever beams—structures that are securely fixed at one end and bear loads at the opposite end. When these beams are subjected to loads within their elastic range, they will return to their...
474
Plastic Deformations01:14

Plastic Deformations

It is essential to understand how structural members behave under plastic deformation when the bending stress exceeds the material's yield strength. This state of deformation permanently alters the shape of the member, in contrast to the linear elastic behavior observed before yielding. The strain at any point in the member is expressed in terms of maximum strain. Notably, the neutral axis, which coincides with the centroid during elastic bending, shifts away from the centroid under plastic...
473
Temperature Dependent Deformation01:12

Temperature Dependent Deformation

In a nonhomogeneous rod made up of steel and brass, restrained at both ends and subjected to a temperature change, several steps are involved in calculating the stress and compressive load. Due to the problem's static indeterminacy, one end support is disconnected, allowing the rod to experience the temperature change freely. Next, an unknown force is applied at the free end, triggering deformations in the rod's steel and brass portions. These deformations are then calculated and added...
413
Deformations in a Symmetric Member in Bending01:18

Deformations in a Symmetric Member in Bending

When analyzing the deformation of a symmetric prismatic member subjected to bending by equal and opposite couples, it becomes clear that as the member bends, the originally straight lines on its wider faces curve into circular arcs, with a constant radius centered at a point known as Point C. This phenomenon helps to understand the stress and strain distribution within the member more clearly.
When the member is segmented into tiny cubic elements, it is observed that the primary stress...
526
Dimensional Analysis03:40

Dimensional Analysis

Dimensional analysis, also known as the factor label method, is a versatile approach for mathematical operations. The main principle behind this approach is: the units of quantities must be subjected to the same mathematical operations as their associated numbers. This method can be applied to computations ranging from simple unit conversions to more complex and multi-step calculations involving several different quantities and their units.
Conversion Factors and Dimensional Analysis
The unit...
65.1K
Deformation of Member under Multiple Loadings01:11

Deformation of Member under Multiple Loadings

When a rod is made of different materials or has various cross-sections, it must be divided into parts that meet the necessary conditions for determining the deformation. These parts are each characterized by their internal force, cross-sectional area, length, and modulus of elasticity. These parameters are then used to compute the deformation of the entire rod.
In the case of a member with a variable cross-section, the strain is not constant but depends on the position. The deformation of an...
488