Related Experiment Video

Updated: Feb 10, 2026

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements
14:18

Automation of Mode Locking in a Nonlinear Polarization Rotation Fiber Laser through Output Polarization Measurements

Published on: February 28, 2016

11.9K

Efficient continuous-wave and passive Q-switched mode-locked Er3+ : CaF2-SrF2 lasers in the mid-infrared region

Jingjing Liu, Xiaoyue Feng, Xiuwei Fan

    Optics Letters
    |May 16, 2018
    PubMed

    More Related Videos

    Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy08:48

    Low-cost Custom Fabrication and Mode-locked Operation of an All-normal-dispersion Femtosecond Fiber Laser for Multiphoton Microscopy

    Published on: November 22, 2019

    8.0K
    Characterizing Far-infrared Laser Emissions and the Measurement of Their Frequencies09:38

    Characterizing Far-infrared Laser Emissions and the Measurement of Their Frequencies

    Published on: December 18, 2015

    12.7K

    Related Concept Videos

    Modes of Standing Waves - I01:03

    Modes of Standing Waves - I

    A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. A building may vibrate for several seconds with a driving frequency matching the building's natural frequency of vibration; this produces a resonance that results in one building collapsing while the neighboring buildings do not. Often, buildings of a certain height are devastated, while other taller buildings remain intact. This...
    4.1K
    Modes of Standing Waves: II01:04

    Modes of Standing Waves: II

    The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions are derived from the physical understanding of how the standing waves are sustained, that is, how the vibrating particles of the medium behave at the boundaries imposed on them.
    For a tube open at one end and closed at the other filled with air, the modes are such that there is always an antinode at the open end and a node at the closed end....
    1.8K
    Switching of BJT01:22

    Switching of BJT

    Switching behavior in Bipolar Junction Transistors (BJTs) is a fundamental aspect utilized in various electronic circuits, particularly for digital logic applications like switches and amplifiers. In a typical switching circuit, a BJT alternates between cut-off and saturation modes, corresponding to the "off" and "on" states, respectively, thus behaving like an ideal switch.
    Cut-off Mode ("Off" State): In this state, both the emitter-base and collector-base junctions are...
    873
    Self-Locking Screw01:16

    Self-Locking Screw

    A square-threaded screw jack is a mechanical device widely used for lifting heavy loads or applying considerable force. One of the key features that can make a screw jack more effective and reliable is its self-locking capability.
    A square-threaded screw jack carrying a load is considered self-locking if the screw retains its position even after the moment applied to it is removed.
    2.5K
    What is a Mode?01:07

    What is a Mode?

    The mode is one of the commonly used measures of a central tendency. It is defined as the most frequent value in a data set.
    There can be more than one mode in a data set if multiple values have the same highest frequency. For instance, suppose that the Statistics exam scores of 20 students are: 50; 53; 59; 59; 63; 63; 72; 72; 72; 72; 72; 76; 78; 81; 83; 84; 84; 84; 90; 93. Here, the mode is 72, as it occurs most frequently, five times.
    A data set with two modes is called bimodal. For example,...
    26.5K
    Passive Filters01:27

    Passive Filters

    Passive filters are utilized to shape the frequency spectrum of signals across a diverse array of applications. These filters, using only passive elements like resistors (R), inductors (L), and capacitors (C), are capable of selectively allowing or blocking certain frequency ranges without the need for external power sources.
    Low-Pass Filters
    Low-pass filters are designed to transmit signals with frequencies lower than the cutoff frequency, ωc, and attenuate those above it. The cutoff...
    1.0K