Related Experiment Video

Updated: Feb 10, 2026

Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection
07:51

Development and Functionalization of Electrolyte-Gated Graphene Field-Effect Transistor for Biomarker Detection

Published on: February 1, 2022

3.8K

Effects of thermal treatment on the adhesion strength and osteoinductive activity of single-layer graphene sheets on

Ming Gu1, Longwei Lv1, Feng Du2

  • 1Department of Prosthodontics, Peking University School and Hospital of Stomatology, 22 Zhongguancun Avenue South, Beijing, 100081, PR China.

Scientific Reports
|May 27, 2018
PubMed

More Related Videos

Fabrication of Three-Dimensional Graphene-Based Polyhedrons via Origami-Like Self-Folding14:52

Fabrication of Three-Dimensional Graphene-Based Polyhedrons via Origami-Like Self-Folding

Published on: September 23, 2018

9.4K
Simultaneous Synthesis of Single-walled Carbon Nanotubes and Graphene in a Magnetically-enhanced Arc Plasma09:48

Simultaneous Synthesis of Single-walled Carbon Nanotubes and Graphene in a Magnetically-enhanced Arc Plasma

Published on: February 2, 2012

15.7K

Related Concept Videos

Ionic Strength: Effects on Chemical Equilibria01:19

Ionic Strength: Effects on Chemical Equilibria

The addition of an inert ionic compound increases the solubility of a sparingly soluble salt. For example, adding potassium nitrate to a saturated solution of calcium sulfate significantly enhances the solubility of calcium sulfate. Le Châtelier's principle cannot predict this shift in the equilibrium. Instead, this could be explained in terms of changes in the effective concentration of the ions in solution in the presence of added inert salt.
In this solution, the primary...
2.7K
Cycloaddition Reactions: MO Requirements for Thermal Activation01:16

Cycloaddition Reactions: MO Requirements for Thermal Activation

Thermal cycloadditions are reactions where the source of activation energy needed to initiate the reaction is provided in the form of heat. A typical example of a thermally-allowed cycloaddition is the Diels–Alder reaction, which is a [4 + 2] cycloaddition. In contrast, a [2 + 2] cycloaddition is thermally forbidden.
4.6K
Adhesion01:14

Adhesion

Adhesion occurs when one type of molecule is attracted to a different molecule. Water exhibits adhesive properties in the presence of polar surfaces, such as glass or cellulose in plants. For instance, when water is poured into a glass, the positively charged hydrogen molecules of water are more attracted to the negatively charged oxygen molecules in the silica than to the oxygen in neighboring water molecules.
Capillary action is a result of water’s adhesive tendencies. When a narrow...
44.5K
Acid Strength and Molecular Structure03:05

Acid Strength and Molecular Structure

Binary Acids and Bases
In the absence of any leveling effect, the acid strength of binary compounds of hydrogen with nonmetals (A) increases as the H-A bond strength decreases down a group in the periodic table. For group 17, the order of increasing acidity is HF < HCl < HBr < HI. Likewise, for group 16, the order of increasing acid strength is H2O < H2S < H2Se < H2Te. Across a row in the periodic table, the acid strength of binary hydrogen compounds increases with increasing...
33.1K
Strength of Cement01:20

Strength of Cement

Strength tests for cement are not performed directly on neat cement paste due to difficulty in obtaining consistent, reliable specimens. Instead, cement is typically tested in the form of cement-sand mortar.
For compressive strength tests, ASTM C 109-05 standards prescribe a cement-sand mix ratio of 1:2.75 and a water/cement ratio of 0.485 for making 2-inch cubes. These cubes are mixed, cast, and cured in saturated lime water at 23°C until testing. Flexural strength testing, outlined in...
518
Relation Between Tensile Strength and Compressive Strength of Concrete01:30

Relation Between Tensile Strength and Compressive Strength of Concrete

Concrete is a fundamental building material, and understanding its strengths is crucial for construction projects. The relationship between its tensile and compressive strengths is intricate, showing that while these strengths are related, they do not increase at the same rate. Tensile strength's growth is slower and is affected by various factors such as the methods used for testing, the size and shape of the specimen, the texture of the aggregate used, and the moisture content of the...
693